Re: VWIC-1MFT-G703 on a Cisco 1721with IOS 12.2(13)T3

ericandre · ‎05-12-2003

When running the above configuration (IOS ver suggested by local Cisco support) a show diag shows the module correctly, but now interfaces or controllers are found in a show ver. If i understood the docu right these should be detected automatically without any further configuration.

Am i missing something, should i try another IOS ver?

(Unfortunately im not very experienced with a 1721)

Thanks, Eric

tepatel · ‎05-13-2003

Ios is fine for 1721 but We need to see following from the router.

sh diag / sh ver /sh run

In sh ver. it should report "E1 multiflex trunk card" or so. Also in sh run, it should report "controller E1 x" as well.

Pl. visit following for more on config. (Later on for your ref.)

http://www-tac.cisco.com/Support_Library/Hardware/WICs/vwic-config.html

ericandre · ‎05-13-2003

Here are sh diag / sh ver.

sh run similarily shows nothing:

V.F.Xira#sh diag

Slot 0:

C1721 1FE Mainboard Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 1.0

PCB Serial Number : FOC06240K1N

Part Number : 73-7546-01

Board Revision : A0

Fab Version : 04

Product Number : Unknown

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 5A 41 01 00 C1 8B 46 4F 43 30 36 32

0x10: 34 30 4B 31 4E 82 49 1D 7A 01 42 41 30 02 04 FF

0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC/VIC Slot 0:

Unknown

Hardware revision 1.0 Board revision B0

Serial number 0029944696 Part number 800-06722-02

FRU Part Number VWIC-1MFT-G703=

Test history 0x00 RMA number 00-00-00

Connector type PCI

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 2F 01 00 01 C8 EB 78 50 1A 42 02 00 00 00 00

0x30: 58 00 00 00 03 02 06 00 FF FF FF FF FF FF FF FF

WIC/VIC Slot 1:

Serial 1T

Hardware revision 1.0 Board revision L0

Serial number 0028142594 Part number 800-01514-01

FRU Part Number WIC-1T=

Test history 0x00 RMA number 00-00-00

Connector type WAN Module

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 02 01 00 01 AD 6C 02 50 05 EA 01 00 00 00 00

0x30: A8 00 00 00 02 04 24 01 FF FF FF FF FF FF FF FF

V.F.Xira#sh ver

Cisco Internetwork Operating System Software

IOS (tm) C1700 Software (C1700-NY-M), Version 12.2(13)T3, RELEASE SOFTWARE (fc2)

TAC Support: http://www.cisco.com/tac

Compiled Tue 11-Mar-03 00:08 by ccai

Image text-base: 0x80008120, data-base: 0x80879144

ROM: System Bootstrap, Version 12.2(7r)XM1, RELEASE SOFTWARE (fc1)

V.F.Xira uptime is 20 hours, 30 minutes

System returned to ROM by power-on

System image file is "flash:c1700-ny-mz.122-13.T3.bin"

cisco 1721 (MPC860P) processor (revision 0x100) with 27235K/5533K bytes of memory.

Processor board ID FOC06240K1N (921721498), with hardware revision 0000

MPC860P processor: part number 5, mask 2

Bridging software.

X.25 software, Version 3.0.0.

1 FastEthernet/IEEE 802.3 interface(s)

1 Serial(sync/async) network interface(s)

32K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

tepatel · ‎05-14-2003

Sorry..correction...wrong url..Here it is

http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120t/120t7/t1_mf_t6.htm

johan.den.hartog · ‎05-14-2003

Hi,

Probably not supported, please visit http://www.cisco.com/en/US/products/hw/routers/ps259/products_data_sheet09186a0080091b9c.html for more details.

Good luck.

Johan

ericandre · ‎05-14-2003

the problem was finnally solved by installing IOS ver 12.2(8) YN.