Cisco Support Community
Community Member

where is Gig-Ethernet ?is the ws6009 wrong?¡¡

I have a 6009,it's three modules,

cisco6009> (enable) sh modul

Mod Slot Ports Module-Type Model Status

--- ---- ----- ------------------------- ------------------- --------

1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE ok

15 1 1 Multilayer Switch Feature WS-F6K-MSFC ok

2 2 8 1000BaseX Ethernet WS-X6408A-GBIC ok

Mod Module-Name Serial-Num

--- ------------------- -----------

1 SAD0426085A

15 SAD04250GZL

2 SAD042705H6

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

1 00-30-7b-96-fd-4a to 00-30-7b-96-fd-4b 3.2 5.3(1) 5.3(5a)CSX

00-30-7b-96-fd-48 to 00-30-7b-96-fd-49

00-d0-01-d0-34-00 to 00-d0-01-d0-37-ff

15 00-30-7b-96-fd-8c to 00-30-7b-96-fd-cb 1.4 12.0(7)XE1 12.0(7)XE1,

2 00-30-b6-3b-f1-f0 to 00-30-b6-3b-f1-f7 1.3 5.4(2) 5.3(5a)CSX

Mod Sub-Type Sub-Model Sub-Serial Sub-Hw

--- ----------------------- ------------------- ----------- ------

1 L3 Switching Engine WS-F6K-PFC SAD042502P4 1.1

But,when i enter router(session 15)

Router#sh hard

Cisco Internetwork Operating System Software


TAC:Home:SW:IOS:Specials for info

Copyright (c) 1986-2000 by cisco Systems, Inc.

Compiled Fri 04-Feb-00 00:28 by lstringr

Image text-base: 0x60008900, data-base: 0x60CBC000

ROM: System Bootstrap, Version 12.0(3)XE, RELEASE SOFTWARE


Router uptime is 15 hours, 56 minutes

System returned to ROM by power-on

Running default software

cisco Cat6k-MSFC (R5000) processor with 122880K/8192K bytes of memory.

Processor board ID SAD04250GZL

R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache

Last reset from power-on

Bridging software.

X.25 software, Version 3.0.0.

123K bytes of non-volatile configuration memory.

4096K bytes of packet SRAM memory.

16384K bytes of Flash internal SIMM (Sector size 256K).

Configuration register is 0x102


I don't kown where are ten Gig-Ethernet?

I use 'setup"

Continue with configuration dialog? [yes/no]: y

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Basic management setup configures only enough connectivity

for management of the system, extended setup will ask you

to configure each interface on the system

Would you like to enter basic management setup? [yes/no]: y

Configuring global parameters:

Enter host name [Router]: cisco6009

The enable secret is a password used to protect access to

privileged EXEC and configuration modes. This password, after

entered, becomes encrypted in the configuration.

Enter enable secret: cisco6009/

The enable password is used when you do not specify an

enable secret password, with some older software versions, and

some boot images.

Enter enable password: cisco

The virtual terminal password is used to protect

access to the router over a network interface.

Enter virtual terminal password: cisco

Configure SNMP Network Management? [no]: n

Current interface summary

Interface IP-Address OK? Method Status Protocol

EOBC0 YES unset up up

Enter interface name used to connect to the

management network from the above interface summary: ocolEOBCo 0

Invalid interface

is the ws6009 wrong ?

Community Member

Re: where is Gig-Ethernet ?is the ws6009 wrong?¡¡

help me !my english is very bad.I hope you understand me


Re: where is Gig-Ethernet ?is the ws6009 wrong?¡¡

It looks like your Catalyst is running in Hybrid OS mode. Catalyst OS handles your switching, and Cisco IOS software handles higher-layer routing. Think of it as CatOS for Layer 2, and IOS for Layer 3; that is not entirely accurate, but it is a start.

In CatOS, assign your Gigabit Ethernet ports to be either VLAN access ports (only one VLAN per port), or VLAN trunk ports (all VLANs).

In IOS, you create or define interfaces for the VLANs, not the Gigabit Ethernet ports. Then, you assign the protocol information to them for routing. For example, if you have two VLANs in CatOS, VLAN1 and VLAN2, and you want to route TCP/IP between them, then in IOS you can do the following:

interface Vlan1

ip address

interface Vlan2

ip address

As for your management interface, enter it exactly as it is spelled: EOBC0, not EOBC 0. It is the only interface listed, because you have not created any of the VLAN interfaces yet.

Also, under IOS software, don't forget to enable routing for the protocols you want to route. Otherwise, you can put all the network addresses you want on the interfaces, but the traffic will go nowhere.

Hope this helps.

CreatePlease to create content