Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Who can told me why?

00:55:19338933932: %SYS-3-CPUHOG: Task ran for 2256 msec (17/10), process = ARP

Input, PC = 803A9048.

-Traceback= 803A904C 80421C98 803BCA7C

  • Other Network Infrastructure Subjects
5 REPLIES
Bronze

Re: Who can told me why?

Can you send "sh ver"?

New Member

Re: Who can told me why?

Yes ,I can .

"Router#sh ver

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-I-M), Version 12.2(2)T, RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support')">http://www.cisco.com/cgi-bin/ibld/view.pl?i=support

Copyright (c) 1986-2001 by cisco Systems, Inc.

Compiled Sat 02-Jun-01 16:05 by ccai

Image text-base: 0x80008088, data-base: 0x809D5278

ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)

ROM: C2600 Software (C2600-I-M), Version 12.2(2)T, RELEASE SOFTWARE (fc1)

Router uptime is 28 minutes

System returned to ROM by power-on

System image file is "flash:c2600-i-mz.122-2.T"

cisco 2611 (MPC860) processor (revision 0x203) with 28672K/4096K bytes of memory.

Processor board ID JAD05310MAU (3192444792)

M860 processor: part number 0, mask 49

Bridging software.

X.25 software, Version 3.0.0.

2 Ethernet/IEEE 802.3 interface(s)

32K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

"

This devie is not being polled by CW2000 RME application.

Thanks .

Blue

Re: Who can told me why?

What IOS version is running on this device and what model is this?. Is this devie is being polled by CW2000 RME application?

New Member

Re: Who can told me why?

This is message from CISCO Error Message Decoder..I hope this help..

1. %SYS-3-CPUHOG: Task ran for [dec] msec ([dec]/[dec]), process = [chars], PC = [hex].

The indicated process has run for too long a period of time without relinquishing the processor. The process is a "CPU hog."

Recommended Action: If this message appears during startup or during OIR of a card, no action is required. If this message appears when accessing a Flash memory device, consider replacing the affected Flash memory device. If this message occurs during normal router operation, it is most probably caused by a software failure. To take advantage of recent fixes, upgrade your system to the latest Cisco IOS software release in your release train.

Related document:

http://www.cisco.com/warp/public/63/cpuhog.shtml

Gold

Re: Who can told me why?

First CPU hogs are always bugs. I would open a TAC case for this. Second, I would examine my configuration carefully for ant issues with the way this box is configured. For instance, if I had to guess, I'd guess that you have a large route or a default route staticlaly configured to some sort of a broadcast interface. For instance, you might have:

ip route 0.0.0.0 0.0.0.0 ethernet 0

This would be a bad thing, since the router must send an arp request for each reachable destination on the ethernet 0 interface, and this will take a lot of processing time and memory. You should always configure statics across a broadcast interface to a next hop, rather than to the interface, if at all possible.

Russ

127
Views
0
Helpful
5
Replies
This widget could not be displayed.