11-25-2003 08:31 PM - edited 03-02-2019 11:58 AM
Hello
I have a new 3725 router and I installed a new WIC-1DSU-T1 but the router does not see the service module. I installed a second new WIC-1DSU-T1 and it still does not see either module...I think I have the wrong IOS image because when you go to config mode and look at the interface menu there is no serial interface option. Here is Sho Ver
User Access Verification
Password:
XXXXXXXXX>en
Password:
XXXXXXXX#show ver
Cisco Internetwork Operating System Software
IOS (tm) 3700 Software (C3725-I-M), Version 12.2(8)T10, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Fri 30-May-03 03:46 by kellythw
Image text-base: 0x60008940, data-base: 0x60AF0000
ROM: System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)
XXXXXXXXXX uptime is 8 hours, 26 minutes
System returned to ROM by power-on
System image file is "flash:c3725-i-mz.122-8.T10.bin"
cisco 3725 (R7000) processor (revision 0.1) with 98304K/32768K bytes of memory.
Processor board ID JHY0729K1RM
R7000 CPU at 240Mhz, Implementation 39, Rev 3.3, 256KB L2 Cache
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
2 FastEthernet/IEEE 802.3 interface(s)
2 Channelized T1/PRI port(s)
DRAM configuration is 64 bits wide with parity disabled.
55K bytes of non-volatile configuration memory.
31744K bytes of ATA System CompactFlash (Read/Write)
Configuration register is 0x2102
XXXXXXXXXXX#show run
Building configuration...
Current configuration : 780 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname XXXXXXXXXXX
!
enable secret 5 $1$JAtr$cztoB4xMk7.3naz4/mOja/
!
ip subnet-zero
!
!
!
!
controller T1 0/0
framing sf
linecode ami
!
controller T1 0/1
framing sf
linecode ami
!
!
!
interface Loopback0
no ip address
!
interface FastEthernet0/0
ip address XXXXXXXXXXXXXXXXXXXX
speed auto
full-duplex
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
router rip
version 2
network XXXXXXXXXXX
network XXXXXXXXXXX
network XXXXXXXXXXXX
!
ip classless
ip route 0.0.0.0 0.0.0.0 XXXXXXXXXXX
ip http server
ip pim bidir-enable
I do have a VWIC-2MFT-T1 that shows up as you can see...suggestions...I also see that a WIC-1DSU-T1-V2 is supprted. Does that mean that the WIC-1DSU-T1 is not supported on the router??????
Thanks
Solved! Go to Solution.
11-25-2003 09:13 PM
You need atleast a 12.2(11)YT image to support WIC-1DSU-T1. This card is not supported in the 3725 in the 12.2(8)T train.
11-25-2003 09:13 PM
You need atleast a 12.2(11)YT image to support WIC-1DSU-T1. This card is not supported in the 3725 in the 12.2(8)T train.
12-01-2003 05:19 AM
Thanks....thats waht I thought and I upgraded to 12.3 and all is well...Thanks for your help and quick response
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: