Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

WIC-1DSU-T1 not recognized by New 3725 router

Hello

I have a new 3725 router and I installed a new WIC-1DSU-T1 but the router does not see the service module. I installed a second new WIC-1DSU-T1 and it still does not see either module...I think I have the wrong IOS image because when you go to config mode and look at the interface menu there is no serial interface option. Here is Sho Ver

User Access Verification

Password:

XXXXXXXXX>en

Password:

XXXXXXXX#show ver

Cisco Internetwork Operating System Software

IOS (tm) 3700 Software (C3725-I-M), Version 12.2(8)T10, RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Fri 30-May-03 03:46 by kellythw

Image text-base: 0x60008940, data-base: 0x60AF0000

ROM: System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)

XXXXXXXXXX uptime is 8 hours, 26 minutes

System returned to ROM by power-on

System image file is "flash:c3725-i-mz.122-8.T10.bin"

cisco 3725 (R7000) processor (revision 0.1) with 98304K/32768K bytes of memory.

Processor board ID JHY0729K1RM

R7000 CPU at 240Mhz, Implementation 39, Rev 3.3, 256KB L2 Cache

Bridging software.

X.25 software, Version 3.0.0.

Primary Rate ISDN software, Version 1.1.

2 FastEthernet/IEEE 802.3 interface(s)

2 Channelized T1/PRI port(s)

DRAM configuration is 64 bits wide with parity disabled.

55K bytes of non-volatile configuration memory.

31744K bytes of ATA System CompactFlash (Read/Write)

Configuration register is 0x2102

XXXXXXXXXXX#show run

Building configuration...

Current configuration : 780 bytes

!

version 12.2

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname XXXXXXXXXXX

!

enable secret 5 $1$JAtr$cztoB4xMk7.3naz4/mOja/

!

ip subnet-zero

!

!

!

!

controller T1 0/0

framing sf

linecode ami

!

controller T1 0/1

framing sf

linecode ami

!

!

!

interface Loopback0

no ip address

!

interface FastEthernet0/0

ip address XXXXXXXXXXXXXXXXXXXX

speed auto

full-duplex

!

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

router rip

version 2

network XXXXXXXXXXX

network XXXXXXXXXXX

network XXXXXXXXXXXX

!

ip classless

ip route 0.0.0.0 0.0.0.0 XXXXXXXXXXX

ip http server

ip pim bidir-enable

I do have a VWIC-2MFT-T1 that shows up as you can see...suggestions...I also see that a WIC-1DSU-T1-V2 is supprted. Does that mean that the WIC-1DSU-T1 is not supported on the router??????

Thanks

1 ACCEPTED SOLUTION

Accepted Solutions

Re: WIC-1DSU-T1 not recognized by New 3725 router

You need atleast a 12.2(11)YT image to support WIC-1DSU-T1. This card is not supported in the 3725 in the 12.2(8)T train.

2 REPLIES

Re: WIC-1DSU-T1 not recognized by New 3725 router

You need atleast a 12.2(11)YT image to support WIC-1DSU-T1. This card is not supported in the 3725 in the 12.2(8)T train.

New Member

Re: WIC-1DSU-T1 not recognized by New 3725 router

Thanks....thats waht I thought and I upgraded to 12.3 and all is well...Thanks for your help and quick response

185
Views
0
Helpful
2
Replies