Re: WIC-1T in NM-1E2W on 3640

robcoc · ‎03-07-2003

Hi,

I have a 3640 with 2 NM-4T and 1 NM-1E2W with a WIC-1T installed. The problem is that the line protocol on the serial connection of the WIC-1T never goes up, even if all the criteria of the link are up. I changed the NM-1E2W with a new one, but nothing changed.

The IOS is c3640-is-mz_120-5_T1 and has 8MB flash and 32MB RAM.

Is an IOS problem?

Is ther anybody who faced my same problem?

Bye and thank you in advance.

Roberto

lgijssel · ‎03-07-2003

It looks your first thought is correct. It is an IOS issue.

This URL shows from what release which module is supported.

That is not your release.

http://www.cisco.com/en/US/products/hw/modules/ps3129/products_tech_note09186a0080093c41.shtml

Looks like you will need an upgrade.

Regards,

Leo

robcoc · ‎03-07-2003

Hi Leo, the link you send me is about the VWIC-1MFT-T1 and not the WIC-1T.

Maybe there is a misunderstanding.

Thank you

Roberto

lgijssel · ‎03-07-2003

You are completely right! Here is the correct one:

http://www.cisco.com/warp/public/107/hw_1t_wic.shtml#plat

And for the NM-1E2W:

http://www.cisco.com/en/US/products/hw/modules/ps2797/products_tech_note09186a00800ad3cc.shtml#platsup

This is not good, it should work. Did you try both WIC-slots?

Still a good weekend!

Leo

robcoc · ‎03-09-2003

Hi, yes I tried both the wic slots.

And from the link you send me I see that the WIC-1T should work....what I think now is that I will change the NM slot where the NM-1E2W is.

Bye

Roberto

gschertz · ‎03-08-2003

Could you provide a copy of the show int serial ?/? for me. What pprotocol are you using, and what is the other end connected to? Also a show service-module could help find the problem.

I have run a 1nm-2e2w with two wic-1t csu/dsu's installed. I first ran c3620-js-mz.120-2.bin. enterprize plus edition.

A show int may help also.

happy routing

Gene

robcoc · ‎03-11-2003

Hi, here there is the output of sh int s0/0 and sh ver. The other end is connected to a 1603R. I tried with both encapsalation (HDLC and PPP).

Thank you.

Roberto

Serial0/0 is up, line protocol is down

Hardware is QUICC Serial

Description: Vignola

Internet address is 192.168.111.1/24

MTU 1500 bytes, BW 19 Kbit, DLY 20000 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation PPP, loopback not set

Keepalive set (10 sec)

DTR is pulsed for 0 seconds on reset, Restart-Delay is 4294967 secs

LCP Listen

Closed: IPCP

Last input never, output never, output hang never

Last clearing of "show interface" counters 00:05:42

Queueing strategy: fifo

Output queue 0/40, 0 drops; input queue 0/75, 0 drops

30 second input rate 0 bits/sec, 0 packets/sec

30 second output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

66 packets output, 924 bytes, 0 underruns

0 output errors, 0 collisions, 19 interface resets

0 output buffer failures, 0 output buffers swapped out

0 carrier transitions

DCD=up DSR=up DTR=up RTS=up CTS=up

------------------ show version ------------------

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3640-IS-M), Version 12.0(5)T1, RELEASE SOFTWARE (fc1)

Compiled Tue 17-Aug-99 21:03 by cmong

Image text-base: 0x600088F0, data-base: 0x60C4C000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

3640_Smov uptime is 13 minutes

System returned to ROM by power-on at 11:16:33 UTC Wed May 5 1993

System image file is "flash:c3640-is-mz_120-5_T1.bin"

cisco 3640 (R4700) processor (revision 0x00) with 28672K/4096K bytes of memory.

Processor board ID 16188705

R4700 CPU at 100Mhz, Implementation 33, Rev 1.0

Bridging software.

X.25 software, Version 3.0.0.

1 Ethernet/IEEE 802.3 interface(s)

9 Serial network interface(s)

DRAM configuration is 64 bits wide with parity disabled.

125K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

t.baranski · ‎03-09-2003

Are you sure it's not an issue with the link itself? Does it come up if you use another router / WIC card?

robcoc · ‎03-09-2003

Hello, it's not a link problem, now the line is working with a 1603 instead of the 3640.

Bye and thank you

Roberto

jolmo · ‎03-11-2003

Why are you using 19 Kbit of bandwith in that serial interface, is that the same that in the 1603 ? I think it's a very strange value.