Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

WIC 2T not showing up

Hi Guys,

I got a 3620 with 2 WIC-2T installed. They are showing up in sh diag, but not in sh controllers. I cant even configure them.

Any ideas?

Thanks

R1#show version

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3620-JK9S-M), Version 12.2(29), RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Wed 11-May-05 12:54 by kellmill

Image text-base: 0x60008930, data-base: 0x61598000

ROM: System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

ROM: 3600 Software (C3620-JK9S-M), Version 12.2(29), RELEASE SOFTWARE (fc3)

R1 uptime is 24 minutes

System returned to ROM by power-on

System image file is "flash:c3620-jk9s-mz.122-29.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

R1# show diag

Slot 0:

        Combo 2E, 2W Port adapter, 4 ports

        Port adapter is analyzed

        Port adapter insertion time unknown

        EEPROM contents at hardware discovery:

        Hardware revision 1.2           Board revision B0

        Serial number     10562122      Part number    800-01171-05

        FRU Part Number:  NM-2E2W=

        Test history      0x0           RMA number     00-00-00

        EEPROM format version 1

        EEPROM contents (hex):

          0x20: 01 1E 01 02 00 A1 2A 4A 50 04 93 05 00 00 00 00

          0x30: 58 00 00 00 98 10 27 17 FF FF FF FF FF FF FF FF

        WIC Slot 0:

        Serial 2T (12in1) WAN daughter card

        Hardware revision 1.0           Board revision B0

        Serial number     34603738      Part number    800-03181-02

        Test history      0x0           RMA number     00-00-00

        Connector type    PCI

        EEPROM format version 1

        EEPROM contents (hex):

          0x20: 01 12 01 00 02 10 02 DA 50 0C 6D 02 00 00 00 00

          0x30: 58 00 00 00 06 01 19 00 FF FF FF FF FF FF FF FF

        WIC Slot 1:

        Serial 2T (12in1) WAN daughter card

        Hardware revision 1.0           Board revision B0

        Serial number     33915163      Part number    800-03181-02

        Test history      0x0           RMA number     00-00-00

        Connector type    PCI

        EEPROM format version 1

        EEPROM contents (hex):

          0x20: 01 12 01 00 02 05 81 1B 50 0C 6D 02 00 00 00 00

          0x30: 58 00 00 00 05 09 12 00 FF FF FF FF FF FF FF FF

R1#sh controllers

Interface Ethernet0/0

Hardware is AMD Unknown

ADDR: 62521ECC, FASTSEND: 6002B918, MCI_INDEX: 0

DIST ROUTE ENABLED: 0

Route Cache Flag: 1

LADRF=0x0000 0x0100 0x0000 0x0000

CSR0  =0x00000072, CSR3  =0x00001044, CSR4  =0x0000491D, CSR15 =0x00000000

CSR80 =0x0000D900, CSR114=0x00000000, CRDA  =0x03D185E0, CXDA  =0x03D188B0

BCR9 =0x00000000 (half-duplex)

HW filtering information:

  Promiscuous Mode Disabled, PHY Addr Enabled, Broadcast Addr Enabled

  PHY Addr=0001.96DE.9A21, Multicast Filter=0x0000 0x0100 0x0000 0x0000

amdp2_instance=0x62523CD4, registers=0x3C100000, ib=0x3D18580

rx ring entries=32, tx ring entries=64

rxring=0x3D185E0, rxr shadow=0x62523F04, rx_head=0, rx_tail=0

txring=0x3D18820, txr shadow=0x62523FB0, tx_head=9, tx_tail=9, tx_count=0

Software MAC address filter(hash:length/addr/mask/hits):

  0xC0:  0  0100.0ccc.cccc  0000.0000.0000         0

spurious_idon=0, filtered_pak=0, throttled=0, enabled=0, disabled=0

rx_framing_err=0, rx_overflow_err=0, rx_buffer_err=0

rx_bpe_err=0, rx_soft_overflow_err=0, rx_no_enp=0, rx_discard=0

tx_one_col_err=0, tx_more_col_err=0, tx_no_enp=0, tx_deferred_err=0

tx_underrun_err=0, tx_late_collision_err=0, tx_loss_carrier_err=138

tx_exc_collision_err=0, tx_buff_err=0, fatal_tx_err=0

hsrp_conf=0, need_af_check=0

tx_limited=0(64)

Interface Ethernet0/1

Hardware is AMD Unknown

ADDR: 62526198, FASTSEND: 6002B918, MCI_INDEX: 0

DIST ROUTE ENABLED: 0

Route Cache Flag: 1

LADRF=0x0000 0x0000 0x0000 0x0000

CSR0  =0x00000004, CSR3  =0x00001044, CSR4  =0x00004915, CSR15 =0x00000000

CSR80 =0x0000D900, CSR114=0x00000000, CRDA  =0x03D3F100, CXDA  =0x03D3F340

BCR9 =0x00000000 (half-duplex)

HW filtering information:

  Promiscuous Mode Disabled, PHY Addr Enabled, Broadcast Addr Enabled

  PHY Addr=0001.96DE.9A22, Multicast Filter=0x0000 0x0000 0x0000 0x0000

amdp2_instance=0x62527FA0, registers=0x3C200000, ib=0x3D3F0A0

rx ring entries=32, tx ring entries=64

rxring=0x3D3F100, rxr shadow=0x625281D0, rx_head=0, rx_tail=0

txring=0x3D3F340, txr shadow=0x6252827C, tx_head=0, tx_tail=0, tx_count=0

Software MAC address filter(hash:length/addr/mask/hits):

spurious_idon=0, filtered_pak=0, throttled=0, enabled=0, disabled=0

rx_framing_err=0, rx_overflow_err=0, rx_buffer_err=0

rx_bpe_err=0, rx_soft_overflow_err=0, rx_no_enp=0, rx_discard=0

tx_one_col_err=0, tx_more_col_err=0, tx_no_enp=0, tx_deferred_err=0

tx_underrun_err=0, tx_late_collision_err=0, tx_loss_carrier_err=0

tx_exc_collision_err=0, tx_buff_err=0, fatal_tx_err=0

hsrp_conf=0, need_af_check=0

tx_limited=0(64)



1 REPLY
New Member

Re: WIC 2T not showing up

It might be worth while for you to take a peek at the supported hardware/IOS table in the following document and confirm that it is supported.


http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b0858.shtml

The line I think may affect you in this case is as follows.

"The NM-1E2W, NM-1E1R2W, and NM-2E2W Network Modules do not have enough performance power to support the WIC-2T due to hardware limitations."

411
Views
0
Helpful
1
Replies
CreatePlease login to create content