05-23-2006 02:08 AM - edited 03-03-2019 03:19 AM
Is it possible to use the new WS-X6148-RJ-45 card with the old supervisor WS-X6K-SUP1A-2GE (running CatOS 6.4(16) ) ?
Thanks, Best Regards
Alessandro Asson
Solved! Go to Solution.
05-23-2006 02:12 AM
Hi Alessandro,
Yes that will work fine. WS-X6148-RJ-45 card will be supported with sup card WS-X6K-SUP1A-2GE having minimum of 6.4(1) release as you are having 6.4(16) this card will work fine.
Have a look at this link
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/relnotes/78_11235.htm
HTH, if yes please rate the post.
Ankur
05-23-2006 02:55 AM
Hi Alessandro,
As per the release note if you are running minimum of 6.4(1) this card will be supported but Cisco recommends to have 6.4(11).
And if you want to have CATOS release 7.x on your supervisor enginer then you need to have minimum of 7.2(2) but Cisco recommends to have 7.6(9).
So it depends which CATOS train you are having on supervisor enginer for 6.x train minimum CATOS reuiqred in 6.4(1) and for 7.x train minimuk CATOS required is 7.2(2).
But if you do not wish to go to 7.x train and you already have 6.4(16) as CATOS release on your supervisor enginer this card will be supported. You can try inserting this card with currenet CATOS which you have on supervisor engine and it shuld work.
Have a look at the release note and serach for this card
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/relnotes/ol_4498.htm
I will appreciate if you rate all post.
Ankur
05-23-2006 02:12 AM
Hi Alessandro,
Yes that will work fine. WS-X6148-RJ-45 card will be supported with sup card WS-X6K-SUP1A-2GE having minimum of 6.4(1) release as you are having 6.4(16) this card will work fine.
Have a look at this link
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/relnotes/78_11235.htm
HTH, if yes please rate the post.
Ankur
05-23-2006 02:48 AM
Hi Ankur,
Thank You for the info. However i found in a Cisco Announcement that the Minimum Catalyst OS for
WS-X6148-RJ-45 is 7.2(2). Should I upgrade the CatOS release ?
Alessandro
05-23-2006 02:55 AM
Hi Alessandro,
As per the release note if you are running minimum of 6.4(1) this card will be supported but Cisco recommends to have 6.4(11).
And if you want to have CATOS release 7.x on your supervisor enginer then you need to have minimum of 7.2(2) but Cisco recommends to have 7.6(9).
So it depends which CATOS train you are having on supervisor enginer for 6.x train minimum CATOS reuiqred in 6.4(1) and for 7.x train minimuk CATOS required is 7.2(2).
But if you do not wish to go to 7.x train and you already have 6.4(16) as CATOS release on your supervisor enginer this card will be supported. You can try inserting this card with currenet CATOS which you have on supervisor engine and it shuld work.
Have a look at the release note and serach for this card
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/relnotes/ol_4498.htm
I will appreciate if you rate all post.
Ankur
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: