10-21-2002 06:38 AM - edited 03-02-2019 02:14 AM
I am from an IP background and I am trying to troubleshoot (with difficulty) an X25 connection.
I am using a 2621 with IOS 12.2 enterprise software. The 2621 is connected into a public X.25 cloud. I am trying to connect to a customer NUA / X25 address without success. The customer has an X.25 device.
I am translating IP packets from our network into X25 packets to be forwarded to the customer.
I have attached the following info:-
Debug output (removed IP addresses / NUA info)
hh02601# show int s0/0
Serial0/0 is up, line protocol is up
Hardware is PowerQUICC Serial
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation X25, loopback not set
X.25 DTE, address xxxxxxx0004, state R1, modulo 8, timer 0
Defaults: idle VC timeout 0
cisco encapsulation
input/output window sizes 2/2, packet sizes 128/128
Timers: T20 180, T21 200, T22 180, T23 180
Channels: Incoming-only none, Two-way 1024-1074, Outgoing-only none
(configuration on Restart: modulo 8,
Window size: input 2 output 2, Packet size: input 128, output 128
Channels: Incoming-only none, Two-way 1024-1073, Outgoing-only none)
RESTARTs 0/0 CALLs 0+9/0+0/0+0 DIAGs 0/0
LAPB DTE, state CONNECT, modulo 8, k 7, N1 12056, N2 20
T1 3000, T2 0, interface outage (partial T3) 0, T4 0
VS 3, VR 1, tx NR 1, Remote VR 3, Retransmissions 0
Queues: U/S frames 0, I frames 0, unack. 0, reTx 0
IFRAMEs 26/0 RNRs 0/0 REJs 0/0 SABM/Es 0/0 FRMRs 0/0 DISCs 0/0
Last input 2w1d, output 00:00:11, output hang never
Last clearing of "show interface" counters 00:20:16
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue :0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
67 packets input, 134 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
67 packets output, 417 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
hh02601#show x25 in
hh02601#show x25 interface ser
hh02601#show x25 interface serial 0/0
SVC 1069, State: P2, Interface: Serial0/0
Started 00:02:52, last input never, output never
Line: 70 vty 4 Location: Host: A
xxxxxx0004 connected to xxxxxxxx3503 PAD <--> X25
Window size input: 2, output: 2
Packet size input: 128, output: 128
P/D state timeouts: 0 timer (secs): 9
data bytes 0/0 packets 0/0 Resets 0/0 RNRs 0/0 REJs 0/0 INTs 0/0
SVC 1070, State: P6, Interface: Serial0/0
Started 00:03:11, last input never, output never
<VC no longer active>
Window size input: 2, output: 2
Packet size input: 128, output: 128
P/D state timeouts: 1 timer (secs): 168
data bytes 0/0 packets 0/0 Resets 0/0 RNRs 0/0 REJs 0/0 INTs 0/0
SVC 1072, State: P2, Interface: Serial0/0
Started 00:03:11, last input never, output never
Line: 69 vty 3 Location: Host: A
0004 connected to 503 PAD <--> X25
Window size input: 2, output: 2
Packet size input: 128, output: 128
P/D state timeouts: 0 timer (secs): 170
data bytes 0/0 packets 0/0 Resets 0/0 RNRs 0/0 REJs 0/0 INTs 0/0
SVC 1073, State: P6, Interface: Serial0/0
Started 00:03:30, last input never, output never
<VC no longer active>
Window size input: 2, output: 2
Packet size input: 128, output: 128
P/D state timeouts: 1 timer (secs): 149
data bytes 0/0 packets 0/0 Resets 0/0 RNRs 0/0 REJs 0/0 INTs 0/0
h
hh02601#show translate
Translate From: TCP host A Port 9801
To: X25 xxxxxxx3503
4/0 users active, 5 peak, 79 total, 57 failures
Translate From: X25 xxxxxxx0004
To: TCP host A Port 9801
0/0 users active, 0 peak, 0 total, 0 failures
hh02601#
*Mar 20 02:10:53.418 UTC: Serial0/0: X.25 O R1 Clear (5) 8 lci 1073
*Mar 20 02:10:53.418 UTC: Cause 0, Diag 50 (DTE originated/Time expired for Clear)
*Mar 20 02:10:56.222 UTC: Serial0/0: X.25 O R1 Clear (5) 8 lci 1071
*Mar 20 02:10:56.222 UTC: Cause 0, Diag 50 (DTE originated/Time expired for Clear)
*Mar 20 02:10:58.350 UTC: Serial0/0: X.25 O R1 Clear (5) 8 lci 1070
*Mar 20 02:10:58.350 UTC: Cause 0, Diag 50 (DTE originated/Time expired for Clear)
2w5d: %X25-7-DIAGEVENT: Interface Serial0/0, X.25 diagnostic event, Time expired for Clear, lci 1072
*Mar 20 02:11:03.906 UTC: Serial0/0: X.25 O R1 Call (22) 8 lci 1072
*Mar 20 02:11:03.906 UTC: From (12): 0004 To (14): 3503
*Mar 20 02:11:03.906 UTC: Facilities: (0)
*Mar 20 02:11:03.906 UTC: Call User Data (4): 0x01000000 (pad)
*Mar 20 02:11:12.318 UTC: Serial0/0: X.25 O R1 Clear (5) 8 lci 1074
*Mar 20 02:11:12.318 UTC: Cause 0, Diag 49 (DTE originated/Time expired for Call)
*Mar 20 02:11:56.654 UTC: Serial0/0: X.25 O R1 Clear (5) 8 lci 1068
*Mar 20 02:11:56.654 UTC: Cause 0, Diag 49 (DTE originated/Time expired for Call)
*Mar 20 02:13:53.418 UTC: Serial0/0: X.25 O R1 Clear (5) 8 lci 1073
*Mar 20 02:13:53.418 UTC: Cause 0, Diag 50 (DTE originated/Time expired for Clear)
*Mar 20 02:13:56.222 UTC: Serial0/0: X.25 O R1 Clear (5) 8 lci 1071
*Mar 20 02:13:56.222 UTC: Cause 0, Diag 50 (DTE originated/Time expired for Clear)
*Mar 20 02:13:58.350 UTC: Serial0/0: X.25 O R1 Clear (5) 8 lci 1070
config
hh02601# wr t
Building configuration...
Current configuration : 1267 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname 2601
!
enable password
!
ip subnet-zero
!
!
!
isdn voice-call-failure 0
x25 routing
call rsvp-sync
!
!
!
!
!
!
controller E1 1/0
!
!
!
interface Loopback0
ip address x.x.x.197 255.255.255.252
!
interface FastEthernet0/0
ip address 255.255.255.0
speed 100
half-duplex
!
interface Serial0/0
bandwidth 64
no ip address
encapsulation x25
no ip mroute-cache
x25 address 0004
x25 ltc 1024
x25 htc 1074
!
interface BRI0/0
no ip address
encapsulation hdlc
shutdown
!
interface FastEthernet0/1
ip address x.x.x.218 255.255.255.252
speed 100
full-duplex
!
interface Serial0/1
no ip address
shutdown
!
!
x25 route 3503 interface Serial0/0
!
translate tcp x.x.x.198 port 9801 x25 3503
translate x25 0004 tcp x.x.x.203 port 9801
!
dial-peer cor custom
!
!
!
!
line con 0
line aux 0
line vty 0 4
password
login
transport input telnet
!
Thanks
10-21-2002 01:55 PM
You are using cisco default values for LAP B and X.25 (layer 2 and layer 3). Does this fit to the DCE site (x25 switch)?
One common problem is the configuration of the virtual channels: incoming, two-way and outgoing.
Edgar
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: