07-25-2006 12:08 AM - edited 03-09-2019 03:41 PM
How to see the native, hybrid mode in 6513 using sh command
07-25-2006 01:29 AM
Hello aksher@cisco,
Type "show ver". Anything that starts with 12.1E or 12.2SX is native. Anything that starts with 5.1-8.5 is hybrid mode.
Also, if you spend a little time on 2 switches (1 running native, the other hybrid), it is quite apparent what mode the switch is running.
A "show ver" from a Native switch
Router# show version
Cisco Internetwork Operating System Software
IOS (tm) c6sup2_rp Software (c6sup2_rp-JSV-M), Version 12.1(nightly.E020626) NIG
HTLY BUILD
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Wed 26-Jun-02 06:20 by
Image text-base: 0x40008BF0, data-base: 0x419BA000
ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1)
Router uptime is 2 weeks, 8 hours, 48 minutes
Time since Router switched to active is 1 minute
System returned to ROM by power-on (SP by power-on)
System image file is "sup-bootflash:c6sup22-jsv-mz"
cisco Catalyst 6000 (R7000) processor with 112640K/18432K bytes of memory.
Processor board ID SAD06210067
R7000 CPU at 300Mhz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
3 Virtual Ethernet/IEEE 802.3 interface(s)
48 FastEthernet/IEEE 802.3 interface(s)
381K bytes of non-volatile configuration memory.
16384K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
Router#
A "show ver" from a Hybrid switch
Console> show version
WS-C6009 Software, Version NmpSW: 6.2(0.11)KEY
Copyright (c) 1995-2000 by Cisco Systems
NMP S/W compiled on Oct 5 2000, 01:18:33
System Bootstrap Version: 5.2(1)
Hardware Version: 1.0 Model: WS-C6009 Serial #: SCA030900JA
Mod Port Model Serial # Versions
--- ---- ------------------- ----------- --------------------------------------
1 2 WS-X6K-SUP1A-2GE SAD03392376 Hw : 1.0
Fw : 5.2(1)
Fw1: 5.1(1)CSX
Sw : 6.2(0.11)KEY
Sw1: 6.2(0.11)KEY
L3 Switching Engine SAD03365068 Hw: 1.0
3 2 WS-X6380-NAM JAB0343055Y Hw : 0.201
Fw : 4B4LZ0XA
Fw1: 4.2(0.24)DAY68
Sw : 1.1(0.20)
Sw1: 6.2(0.11)KEY
5 48 WS-X6248-RJ-45 SAD03181291 Hw : 1.0
Fw : 4.2(0.24)VAI78
Sw : 6.2(0.11)KEY
15 1 WS-F6K-MSFC SAD03366264 Hw : 1.2
Fw : 12.1(2)E,
Sw : 12.1(2)E,
DRAM FLASH NVRAM
Module Total Used Free Total Used Free Total Used Free
------ ------- ------- ------- ------- ------- ------- ----- ----- -----
1 65408K 45402K 20006K 16384K 8683K 7701K 512K 253K 259K
Uptime is 1 day, 19 hours, 54 minutes
Console> (enable)
Hope that helps! If so, please rate.
Thanks
07-25-2006 02:56 AM
how to switchover between these two modes.
07-25-2006 03:18 AM
Hello aksher@cisco,
This is not a trivial task. Here are links for both conversions.
System Software Conversion from CatOS to Cisco IOS for Catalyst 6500/6000 Switches
http://www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008015bfa6.shtml
System Software Conversion from Cisco IOS to CatOS for Catalyst 6500/6000 Switches
http://www.cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a00801350b8.shtml
Hope that helps! If so, please rate.
Thanks
07-25-2006 08:28 PM
i had meant on how to switchover to different modes in FWSM and the corresponding changes that needs to be done on FWSM.you have asked to change CatOS to IOS
07-25-2006 08:42 PM
Actually you asked "How to see the native, hybrid mode in 6513 using sh command" That is why I posted what I posted. I saw you posted another message asking about transparent mode. I too sent you a link there with instructions on what needs to be done. Hope that helps!
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: