Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

ADM(Anomaly Dectector Module) PowerDown Failure in upgrade process.

hellow, everyone.

i'm yunchouljung in korea

i have a question about ADM module power down issue.

i had upgraded AGM Module successfully in version 6.1.2 to 6.1.6

but failed ADM Module upgrade in version 6.1.2 to 6.1.6

i uploaded a AP images in MP status and enterd "hw-module module 12 reset cf:4" command.

(i waited a message "you can now reset the module....")

after a reset process, ADM module disabled by SCP dnld Failure.

so, i enabled a power on ADM Module but result is same.

my upgrade process is below.

1.     hw-module module 12 reset cf:1

2.     copy ftp://anonymous@x.x.x.x/c6svc-adm1G-k9.6-1-6.bin pclc#12-fs:

3.     hw-module module 12 reset cf:4

anybody help me?

thanks in advance.

p.s : i have already tested other ios version and ap/mp images.

================================================================

the module version and log is below.

Router_OUT#sh module

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  2    3  Anomaly Guard Module                   WS-SVC-AGM-1-K9   

  3   16  16 port 1000mb GBIC ethernet           WS-X6416-GBIC     

  5   48  SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX    

  7    2  Supervisor Engine 720 (Active)         WS-SUP720-3B      

  9    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE     

10    8  Network Analysis Module                WS-SVC-NAM-2      

12    3  Anomaly Detector Module                WS-SVC-ADM-1-K9   

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  2  0017.e067.ec6c to 0017.e067.ec73   2.0   7.2(1)       6.1(6)       Ok

  3  000e.d73c.3d40 to 000e.d73c.3d4f   2.5   5.4(2)       8.5(0.46)RFW Ok

  5  0015.2bfe.c130 to 0015.2bfe.c15f  10.1   7.2(1)       8.5(0.46)RFW Ok

  7  0016.c85e.3aa0 to 0016.c85e.3aa3   5.2   8.4(2)       12.2(18)SXF1 Ok

  9  001b.d45d.f890 to 001b.d45d.f893   2.6   12.2(14r)S5  12.2(18)SXF1 Ok

10  0003.fead.7592 to 0003.fead.7599   2.0   7.2(1)       4.0(1)       Ok

12  0012.80f1.1ae8 to 0012.80f1.1aef   1.0   7.2(1)       8.5(0.46)RFW PwrDown

Mod  Sub-Module                  Model              Serial       Hw     Status

---- --------------------------- ------------------ ----------- ------- -------

  7  Policy Feature Card 3       WS-F6K-PFC3B       SAL10478K1R  2.3    Ok

  7  MSFC3 Daughterboard         WS-SUP720          SAL104892TJ  2.5    Ok

  9  Centralized Forwarding Card WS-F6700-CFC       SAL1124QX44  3.1    Ok

Mod  Online Diag Status

---- -------------------

  2  Pass

  3  Pass

  5  Pass

  7  Pass

  9  Pass

10  Pass

12  Not Applicable

Router_OUT#

47w1d: SP: The PC in slot 2 is shutting down. Please wait ...

47w1d: SP: shutdown_pc_process:No response from module 2

Jul 13 16:54:49: %C6KPWR-SP-4-DISABLED: power to module in slot 2 set off (Reset)

47w1d: SP: OS_BOOT_STATUS(2) MP OS Boot Status: finished booting

Jul 13 16:56:50: %DIAG-SP-6-RUN_MINIMUM: Module 2: Running Minimal Diagnostics...

Jul 13 16:56:57: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been disabled.

Jul 13 16:56:57: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics

Jul 13 16:56:57: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are now online

Jul 13 16:56:58: %SVCLC-5-FWTRUNK: Firewalled VLANs configured on trunks

Jul 13 17:32:23: %SVCLC-SP-5-STRRECVD: mod 2: <Application upgrade has started>

Jul 13 17:32:23: %SVCLC-SP-5-STRRECVD: mod 2: <Do not reset the module till upgrade completes!!>

Jul 13 17:42:11: %SVCLC-SP-5-STRRECVD: mod 2: <Application upgrade has succeeded>

Jul 13 17:42:11: %SVCLC-SP-5-STRRECVD: mod 2: <You can now reset the module>

47w1d: SP: The PC in slot 2 is shutting down. Please wait ...

47w1d: SP: PC shutdown completed for module 2

Jul 13 17:42:57: %C6KPWR-SP-4-DISABLED: power to module in slot 2 set off (Reset)

47w1d: SP: OS_BOOT_STATUS(2) Anomaly Guard OS Boot Status: finished booting

Jul 13 17:45:03: %DIAG-SP-6-RUN_MINIMUM: Module 2: Running Minimal Diagnostics...

Jul 13 17:45:06: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been disabled.

Jul 13 17:45:06: %DIAG-SP-6-DIAG_OK: Module 2: Passed Online Diagnostics

Jul 13 17:45:06: %OIR-SP-6-INSCARD: Card inserted in slot 2, interfaces are now online

Jul 13 17:45:07: %SVCLC-5-FWTRUNK: Firewalled VLANs configured on trunks

47w1d: SP: The PC in slot 12 is shutting down. Please wait ...

47w1d: SP: shutdown_pc_process:No response from module 12

Jul 13 17:53:29: %C6KPWR-SP-4-DISABLED: power to module in slot 12 set off (Reset)

47w1d: SP: OS_BOOT_STATUS(12) MP OS Boot Status: finished booting

Jul 13 17:55:30: %DIAG-SP-6-RUN_MINIMUM: Module 12: Running Minimal Diagnostics...

Jul 13 17:55:37: %MLS_RATE-4-DISABLING: The Layer2 Rate Limiters have been disabled.

Jul 13 17:55:36: %DIAG-SP-6-DIAG_OK: Module 12: Passed Online Diagnostics

Jul 13 17:55:37: %OIR-SP-6-INSCARD: Card inserted in slot 12, interfaces are now online

Jul 13 18:26:27: %SVCLC-SP-5-STRRECVD: mod 12: <Application upgrade has started>

Jul 13 18:26:27: %SVCLC-SP-5-STRRECVD: mod 12: <Do not reset the module till upgrade completes!!>

Jul 13 18:37:05: %SVCLC-SP-5-STRRECVD: mod 12: <Application upgrade has succeeded>

Jul 13 18:37:05: %SVCLC-SP-5-STRRECVD: mod 12: <You can now reset the module>

47w1d: SP: The PC in slot 12 is shutting down. Please wait ...

47w1d: SP: PC shutdown completed for module 12

Jul 13 18:38:35: %C6KPWR-SP-4-DISABLED: power to module in slot 12 set off (Reset)

Jul 13 18:46:04: %C6KPWR-SP-4-DISABLED: power to module in slot 12 set off (Module  Failed SCP dnld)

Jul 13 18:53:54: %OIR-SP-6-REMCARD: Card removed from slot 12, interfaces disabled

Jul 13 19:01:28: %C6KPWR-SP-4-DISABLED: power to module in slot 12 set off (Module  Failed SCP dnld)

Everyone's tags (1)
873
Views
0
Helpful
0
Replies