05-30-2008 07:16 AM - edited 02-21-2020 03:45 PM
I have setup remote VPN access on a ASA 5505 but cannot access the host or ASA when I login using the VPN. I can connect with the Cisco VPN client and the VPN light is on on the ASA and it shows that I'm connected. I have the correct Ip address but I cannot ping or connect to any of the internal addresses. I cannot find what I'm missing. I have the VPN bypassing the interface ACLs. Since I can login but not go anywhere I feel certian I missed something.
part of config below
interface Vlan1
nameif inside
security-level 100
ip address 10.1.1.1 255.255.255.0
ip local pool xxxx 10.1.1.50-10.1.1.55 mask 255.255.255.0
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 40 set pfs
crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-SHA
crypto dynamic-map inside_dyn_map 20 set pfs
crypto dynamic-map inside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic inside_dyn_map
crypto map inside_map interface inside
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
service-policy global_policy global
group-policy xxxxxxx internal
group-policy xxxxxxx attributes
banner value xxxxx Disaster Recovery Site
wins-server none
dns-server value 24.xxx.xxx.xx
vpn-access-hours none
vpn-simultaneous-logins 3
vpn-idle-timeout 30
vpn-session-timeout none
vpn-filter none
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelall
default-domain none
secure-unit-authentication disable
user-authentication disable
user-authentication-idle-timeout none
ip-phone-bypass disable
leap-bypass disable
nem disable
nac disable
nac-sq-period 300
nac-reval-period 36000
nac-default-acl none
address-pools value xxxxxx
smartcard-removal-disconnect enable
client-firewall none
webvpn
functions url-entry
vpn-nac-exempt none
no vpn-addr-assign aaa
no vpn-addr-assign dhcp
tunnel-group xxxx type ipsec-ra
tunnel-group xxxx general-attributes
address-pool xxxx
default-group-policy xxxx
tunnel-group blountdr ipsec-attributes
pre-shared-key *
Solved! Go to Solution.
06-02-2008 12:47 PM
You are missing nat exemption for the vpn clients. Add the following and you should be good to go.
access-list inside_nat0_outbound extended permit ip any 192.168.10.0 255.255.255.0
nat (inside) 0 access-list inside_nat0_outbound
05-30-2008 07:22 AM
If you can post the config, that would be great.
05-30-2008 09:48 AM
I get the banner and IP adress info...
This is what the client log provides...
1 13:45:32.942 05/30/08 Sev=Warning/2 CVPND/0xE3400013
AddRoute failed to add a route: code 87
Destination 172.20.255.255
Netmask 255.255.255.255
Gateway 10.1.2.1
Interface 10.1.2.5
2 13:45:32.942 05/30/08 Sev=Warning/2 CM/0xA3100024
Unable to add route. Network: ac14ffff, Netmask: ffffffff, Interface: a010205, Gateway: a010201.
06-02-2008 11:01 AM
06-02-2008 12:47 PM
You are missing nat exemption for the vpn clients. Add the following and you should be good to go.
access-list inside_nat0_outbound extended permit ip any 192.168.10.0 255.255.255.0
nat (inside) 0 access-list inside_nat0_outbound
07-09-2008 12:20 AM
I'm having exactly the same problem even though I have the nat exemption entries exactly as stated here.
I've redone the configuration several time with exactly the same result.
07-09-2008 12:52 AM
open a new topic, attach configs, give full description of the problem.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: