Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

mx
New Member

ASA failover isnt working

I am trying to get 2 ASA's to failover in the lab but Im not having any success:

kentasa1# sho fail

Failover On

Failover unit Primary

Failover LAN Interface: failover GigabitEthernet0/3.1 (Failed - No Switchover)

Unit Poll frequency 1 seconds, holdtime 15 seconds

Interface Poll frequency 5 seconds, holdtime 25 seconds

Interface Policy 1

Monitored Interfaces 3 of 250 maximum

failover replication http

Version: Ours 7.2(1), Mate Unknown

Last Failover at: 10:21:03 EST Sep 19 2006

This host: Primary - Active

Active time: 1126090 (sec)

slot 0: ASA5520 hw/sw rev (1.1/7.2(1)) status (Up Sys)

Interface management (10.0.10.10): Normal (Waiting)

Interface inside (10.254.0.2): No Link (Waiting)

Interface outside (206.67.136.3): No Link (Waiting)

Interface dmz (192.168.1.3): No Link (Not-Monitored)

Interface mtadmz (192.168.255.1): No Link (Not-Monitored)

slot 1: empty

Other host: Secondary - Failed

Active time: 0 (sec)

slot 0: empty

Interface management (0.0.0.0): Unknown (Waiting)

Interface inside (10.254.0.252): Unknown (Waiting)

Interface outside (206.67.136.253): Unknown (Waiting)

Interface dmz (192.168.1.253): Unknown (Not-Monitored)

Interface mtadmz (192.168.255.253): Unknown (Not-Monitored)

slot 1: empty

Stateful Failover Logical Update Statistics

Link : failover GigabitEthernet0/3.1 (Failed)

Stateful Obj xmit xerr rcv rerr

General 0 0 0 0

sys cmd 0 0 0 0

up time 0 0 0 0

RPC services 0 0 0 0

TCP conn 0 0 0 0

UDP conn 0 0 0 0

ARP tbl 0 0 0 0

Xlate_Timeout 0 0 0 0

VPN IKE upd 0 0 0 0

VPN IPSEC upd 0 0 0 0

VPN CTCP upd 0 0 0 0

VPN SDI upd 0 0 0 0

VPN DHCP upd 0 0 0 0

Logical Update Queue Information

Cur Max Total

Recv Q: 0 0 0

Xmit Q: 0 0 0

I went through the docs but I think Im doing everything right. Attached are the configs to see if I missed anything. Thank you!

Bob

1 ACCEPTED SOLUTION

Accepted Solutions
New Member

Re: ASA failover isnt working

First off, it doesn't look the Failover Interface is up. It should look like:

Failover LAN Interface: FAILOVER GigabitEthernet0/3 (up)

Also, a sh int on your failover interface should show that it is up/up.

-Jon

2 REPLIES
New Member

Re: ASA failover isnt working

First off, it doesn't look the Failover Interface is up. It should look like:

Failover LAN Interface: FAILOVER GigabitEthernet0/3 (up)

Also, a sh int on your failover interface should show that it is up/up.

-Jon

mx
New Member

Re: ASA failover isnt working

UGH Youre right! Thank you!

as soon as I did a no shut, it all came to life.

Thank you much!

2936
Views
0
Helpful
2
Replies
CreatePlease login to create content