Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Gigabit on ASA 5510

Hi,

How would one go about setting the 1000Mbps speed to a ASA 5510 with the "security plus" license?

This is what I'm getting on any interface:

fw(config-if)# speed ?

interface mode commands/options:

10 Force 10 Mbps operation

100 Force 100 Mbps operation

auto Enable AUTO speed configuration

Thanks.

Gabi

1 ACCEPTED SOLUTION

Accepted Solutions

Re: Gigabit on ASA 5510

I thhink you should upgrede to 8.0(3)

I have asa 5510 with security plus license.

Cisco Adaptive Security Appliance Software Version 7.2(3)

ASA5510(config-if)#

ASA5510# conf t

ASA5510(config)# int e0/0

ASA5510(config-if)# spe

ASA5510(config-if)# speed ?

interface mode commands/options:

10 Force 10 Mbps operation

100 Force 100 Mbps operation

1000 Force 1000 Mbps operation

auto Enable AUTO speed configuration

11 REPLIES

Re: Gigabit on ASA 5510

hi,

please post output of the command

"show int ip bri"

Gold

Re: Gigabit on ASA 5510

with the sec+ license, only interfaces 0 and 1 are gig enabled. the others are only 10/100.

http://www.cisco.com/en/US/products/ps6120/prod_models_comparison.html

Community Member

Re: Gigabit on ASA 5510

... and still I can't set eighter e0/0 or e0/1 to gigabit.

Community Member

Re: Gigabit on ASA 5510

fw(config)# sh int ip bri

Interface IP-Address OK? Method Status Protocol

Ethernet0/0 xxx.xxx.xxx.xxx YES CONFIG up up

Ethernet0/1 xxx.xxx.xxx.xxx YES CONFIG up up

Ethernet0/2 unassigned YES unset administratively down down

Ethernet0/3 unassigned YES unset administratively down down

Management0/0 unassigned YES unset administratively down down

Re: Gigabit on ASA 5510

Beginning with Cisco ASA Software v7.2.3, the ASA 5510 Security Plus license enables 2 10/100/1000 interfaces and 3 10/100 interfaces

What Cisco ASA Software do you have?

Community Member

Re: Gigabit on ASA 5510

Yes, I know about that, thank you.

I have version 8.0(2), Security Plus license.

Do any of you know how this works - it's set automatically to 1Gbps or do you need to set it.

Thanks.

Re: Gigabit on ASA 5510

I thhink you should upgrede to 8.0(3)

I have asa 5510 with security plus license.

Cisco Adaptive Security Appliance Software Version 7.2(3)

ASA5510(config-if)#

ASA5510# conf t

ASA5510(config)# int e0/0

ASA5510(config-if)# spe

ASA5510(config-if)# speed ?

interface mode commands/options:

10 Force 10 Mbps operation

100 Force 100 Mbps operation

1000 Force 1000 Mbps operation

auto Enable AUTO speed configuration

Community Member

Re: Gigabit on ASA 5510

Is this a known bug?

Given that I have a version higher that 7.2(3) I should have this option too...

Re: Gigabit on ASA 5510

Its not a 'bug'. Cisco maintains multiple versions at once 7.0.x 7.2.x 8.0.x etc. So it doesnt mean 7.2(3) is older than 8.0(2).

Regards

Farrukh

Community Member

Re: Gigabit on ASA 5510

I've upgraded to 8.0(4). Now it works although there is no mention in the release notes about this.

Thanks!

Gabi

Re: Gigabit on ASA 5510

Thanks for the update and I'm glad you have it working now :).

But I just checked the release notes and its mentioned there albeit in a slightly covert manner :)

CSCsl53995

5510 interface can be set to1000Mbps with base license

Regards

Farrukh

3716
Views
5
Helpful
11
Replies
CreatePlease to create content