Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

how to load System image file in a router

Sir,

How can we copy a system image file through flash in a router series of

CISCO 1700 series.

2 REPLIES

Re: how to load System image file in a router

Hi

You can make use of copy tftp flash command to get the ios (system image) copied from the external TFTP server to the flash device of the router.

do find the other steps required for sucessful uploading of ios code to ur flash device..

Specify the IP address of the TFTP server.

When prompted, enter the IP address of the TFTP server as shown here:

Address or name of remote host []? 10.10.10.2

Specify the filename of the new Cisco IOS Software image.

When prompted, enter the filename of the Cisco IOS Software image to be installed, as shown here:

Source filename []? c2600-i-mz.121-14.bin

Note: The filename is case sensitive, so ensure that you enter it correctly.

Specify the destination filename.

This is the name the new software image will have when it is loaded onto the router. The image can be named anything, but the common practice is to enter the same image filename.

Destination filename []? c2600-i-mz.121-14.bin

Note: The following error message indicates that Flash does not have enough memory to copy the image.

%Error copying tftp://10.10.10.2/c2600-i-mz.121-14.bin

(Not enough space on device)Note: In this case, you need to erase some files before you copy the new image from the TFTP server.

Upgrade the new image from a TFTP server.

2610#copy tftp flash

Address or name of remote host []? 10.10.10.2

Source filename []? c2600-i-mz.121-14.bin

Destination filename [c2600-i-mz.121-14.bin]?y

Accessing tftp://10.10.10.2/c2600-i-mz.121-14.bin...

Erase flash: before copying? [confirm]y

!--- If there is not enough memory available, erase the Flash.

Erasing the flash filesystem will remove all files! Continue? [confirm]y

Erasing device... eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee

eeeeeeeeee ...erased

Erase of flash: complete

Loading c2600-i-mz.121-14.bin from 10.10.10.2 (via Ethernet0/0): !!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

[OK - 4501480/9001984 bytes]

Verifying checksum... OK (0xAC8A)

4501480 bytes copied in 56.88 secs (80383 bytes/sec)

Also check this link for more info..

http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a00801fc986.shtml

regds

New Member

Re: how to load System image file in a router

thanq

regards

jogarao.M

366
Views
0
Helpful
2
Replies