Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

PIX 501 configuration help needed

Hi,

the genius in our U.S. Head Office decided to replace the Watchguard firewalls in our U.K. office with a Cisco PIX 501, before getting me trained. Therefore I need help!!! At the moment all users can get online as the firewall is setup mainly with the default PAT configuration. However, I have to configure some port redirection for various services. My firewalls external IP is 217.206.x.x and I need:

TCP ports 5631 and 3000 and UDP ports 5632 and 5633 to go to internal IP 192.168.13.1

TCP port 5633 and UDP port 5634 to go to internal IP 192.168.13.21

Please help, my current configration is below:

PIX Version 6.3(1)

interface ethernet0 auto

interface ethernet1 100full

nameif ethernet0 outside security0

nameif ethernet1 inside security100

enable password xxxxxxxxxxxxxxxx encrypted

passwd xxxxxxxxxxxxxxxx encrypted

hostname UKPIX

domain-name ciscopix.com

fixup protocol ftp 21

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol http 80

fixup protocol http 3000

fixup protocol ils 389

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol sip 5060

fixup protocol sip udp 5060

fixup protocol skinny 2000

fixup protocol smtp 25

fixup protocol sqlnet 1521

names

pager lines 24

mtu outside 1500

mtu inside 1500

ip address outside 217.206.x.x 255.255.255.248

ip address inside 192.168.13.2 255.255.255.0

ip audit info action alarm

ip audit attack action alarm

pdm location 81.168.x.x 255.255.255.255 outside

pdm location 64.208.x.x 255.255.255.255 outside

pdm location 81.168.x.0 255.255.255.255 outside

pdm location 195.137.x.x 255.255.255.255 outside

pdm logging informational 100

pdm history enable

arp timeout 14400

global (outside) 1 interface

nat (inside) 1 0.0.0.0 0.0.0.0 0 0

route outside 0.0.0.0 0.0.0.0 217.206.x.x 1

timeout xlate 0:05:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00

timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00

timeout uauth 0:05:00 absolute

aaa-server TACACS+ protocol tacacs+

aaa-server RADIUS protocol radius

aaa-server LOCAL protocol local

aaa authentication ssh console LOCAL

http server enable

http 0.0.0.0 0.0.0.0 outside

http 192.168.13.0 255.255.255.0 inside

http 0.0.0.0 0.0.0.0 inside

no snmp-server location

no snmp-server contact

snmp-server community public

no snmp-server enable traps

floodguard enable

telnet 0.0.0.0 0.0.0.0 outside

telnet 81.168.x.x 255.255.255.255 outside

telnet 0.0.0.0 0.0.0.0 inside

telnet timeout 5

ssh 64.208.x.x 255.255.255.255 outside

ssh 81.168.x.x 255.255.255.255 outside

ssh 195.137.x.x 255.255.255.255 outside

ssh 0.0.0.0 0.0.0.0 inside

ssh timeout 5

console timeout 0

dhcpd address 192.168.13.3-192.168.13.34 inside

dhcpd lease 3600

dhcpd ping_timeout 750

dhcpd auto_config outside

username xxxxxxxx password xxxxxxxxx encrypted privilege 15

terminal width 80

Cryptochecksum:xxxx

: end

Thanks.

2 REPLIES
Gold

Re: PIX 501 configuration help needed

Mick,

What you require is port re-direction on your PIX, have a read of the following document (under port re-direction):

http://www.cisco.com/warp/public/707/28.html

Let me know if this helps or you require further help/advice.

Jay.

Anonymous
N/A

Re: PIX 501 configuration help needed

Thanks, this and an email for a colleague have helped me get sorted.

Thanks.

148
Views
0
Helpful
2
Replies
CreatePlease to create content