Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Pix 515 635 upgrade errors

So I have this pix 515 that was donated for use in a lab environment for testing, I already got my activation key for 6.35... but during the tftp upgrade in monitor mode i get <11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11><11>.<11>

on my tftp server it shows download percent of 0-300% and so forth. the pix then reboots and takes me to the spot to enter the activation key provided by cisco. I enter the key and get 2 checksum image failures and it reboots... that process will repeat and i cant do anything with it ???

I was wondering if RAM is the culprit. I dont want to buy ram for it if it could be something else causing the issue.

MikeG

2 REPLIES
New Member

Re: Pix 515 635 upgrade errors

Here is the output after the reboot

>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.<11><11><11><11><11><11>.

Received 2101248 bytes

Cisco Secure PIX Firewall admin loader (3.0) #0: Thu Aug 4 21:23:30 PDT 2005

Flash=i28F640J5 @ 0x300

BIOS Flash=AT29C257 @ 0xd8000

imgsum_config: sumval(0xa022) md5(0x95976a4b 0x32251156 0x983b9a46 0x2770e99a)

imgsum_verify: chksum(0x0 ) md5(0xe6cbef77 0x153360b3 0x288fcaaf 0xb6db80cb)

Checksum verification on flash image failed.

Serial Number: 480340522 (0x1ca16a2a)

Enter Activation Key

Part 1 of 4:

New Member

Re: Pix 515 635 upgrade errors

I have not got anything to help, just to state that I have the same problem. I have inherited a PIX following an aquisition and it will not boot. I get the 'Checksum verification on flash image failed' message.

I succesfully uploaded pix635 image, without seeing any of the output you have on your tftp server. When I reloaded I also got the same message annd the Enter Activation Key prompt.

I would like to try erasedisk.bin but I suspect faulty hardware.

181
Views
0
Helpful
2
Replies