02-12-2003 03:09 AM - edited 02-20-2020 10:33 PM
Hi all,
Do you know where I can learn more about pix 6.3?
802.1Q is one of the features I need details.
Thanks
Stephane
02-12-2003 08:31 AM
6.3 is scheduled to be released in the March/April timeframe. The Beta is available now. To get the image and documentation (features and bugs):
- ftp to ftp-eng.cisco.com
- cd to dir pix/pix63-beta
- you will find 4 files to download (readme files and the bin)
Download the Beta and test it out to see for yourself.
Here are a list of new features in 6.3:
VLAN
OSPF
Syslog by ACL
DHCP Relay
DHCP Server on any Interface
HTTPS Authentication Proxy
HTTPS and FTP Filtering via Websense
PPTP Fixup
PAT for Single ESP tunnel
Cut-through Proxy Authentication Using Local Database
Support for New VPN Accelerator Card (VAC+)
User-level Authentication
Concentrator Load Balancing Support
Push Down Backup Concentrator List
Configurable Policy for Internet Access
Backup Concentrator Rollover Latency Reduction
X.509 Certificate Support for PIX VPN Hardware Client
Verify Certificate Distinguished Name
Flexible Easy VPN Management Solutions
NAT Traversal
AES
Diffie Hellman (DH) Group 5 support
MAC-based AAA Exemption
H.323 v3/v4
CTIQBE Fixup
MGCP Fixup
PAT for Skinny
Configurable SIP UDP Fixup
Login Banner
Comments for ACLs
Stack Trace in Flash
Timer on Console
Show Output Filter
Show Tech Enhancements
Assignable Level for Syslogs
"No debug all" and "Undebug all" Commands
License in "Show Version" Output
Interface as Address in ACLs
"Debug AAA" Command
Line Numbers in ACLs
Display Syslogs and Their Levels
Fixup Protocol ICMP Error
Unique Device ID for Syslog Messages
Log All To-the-PIX Access Requests
501 VPN Peer Limit of Ten
501 Unlimited User License Option
GE Interface Settings
PIX Hostname Limit of 63 Characters
IKE with Source Port Other Than UDP/500
Default Interface IP Address
Hope it helps.
Steve
03-26-2003 07:59 PM
Could someone provide a little clarity regarding memory requirements for the PIX 501 and the 6.3 image? .
At this time the PIX 501only comes with 16 Meg.
On the software download page the statement is that it requires 32 Meg.
http://www.cisco.com/cpropart/salestools/cc/pd/fw/sqfw500/prodlit/pix63_ds.htm#50430 states that minimum RAM is "32 megabytes (MB), except the Cisco PIX 501 Security Appliance, which requires 16 MB "
Any guidance would be appreciated
03-26-2003 08:16 PM
Even though the memory requirement say 32MB the file will still load and run on a 501. I will try to search for a link in a bit to show you but it's late and I have a headache so I make no promises ;--
03-26-2003 08:24 PM
Here ya' go, Scroll almost to the bottom of the page where the memory requirements are and you will see where it says 32 MBs required yada yada yada except for the PIX 501 yada yada yada 16MBs. Same story for the flash
It's late and I am going to bed now. Good night zzzzzz
02-20-2003 11:48 AM
1) Cisco PIX 500 Series Firewalls
This data sheet describes the features and options of the Cisco Secure PIX Firewall Software 6.3.
For more information, please see:
http://www.cisco.com/cpropart/salestools/cc/pd/fw/sqfw500/prodlit/pix63_ds.htm
-----------------------------------------------------
2) Cisco PIX 500 Series Firewalls
Cisco PIX. Device Manager is a feature-rich, graphical tool providing enterprise and service providers with an easy-to-use management facility for Cisco PIX Firewalls.
For more information, please see:
http://www.cisco.com/cpropart/salestools/cc/pd/fw/sqfw500/prodlit/pixd3_ds.htm
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: