Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

PIX EXPERTS PLEASE CHECK THIS CONFIG AND HELP ME OUT

Configutarion:-

nameif ethernet0 outside security0

nameif ethernet1 inside security100

nameif ethernet2 dmz security50

hostname pixfirewall

fixup protocol ftp 21

fixup protocol http 80

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol ils 389

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol smtp 25

fixup protocol sqlnet 1521

fixup protocol sip 5060

fixup protocol skinny 2000

names

access-list 102 permit tcp any host x.x.x.x(mail server ip) eq domain

access-list 102 permit udp any host x.x.x.x(mailserver ip) eq domain

access-list 102 permit tcp any host x.x.x.x(mail server ip) eq lotusnotes

access-list 102 permit tcp any host x.x.x.x(mail server ip) eq smtp

access-list 150 permit ip 10.0.0.0 255.0.0.0 host (email server in dmz)

access-list 150 permit ip 172.40.0.0 255.255.0.0 host x.x.x.x(email server in dmz

pager lines 24

interface ethernet0 10baset

interface ethernet1 10baset

interface ethernet2 auto

mtu outside 1500

mtu inside 1500

mtu dmz 1500

ip address outside x.x.x.x 255.255.255.240

ip address inside 10.1.1.1 255.0.0.0

ip address dmz x.x.x.x 255.255.255.240

ip audit info action alarm

ip audit attack action alarm

no pdm history enable

arp timeout 14400

global (outside) 1 x.x.x.x(using-pat) netmask 255.255.255.255

nat (inside) 0 access-list 150

nat (inside) 1 0.0.0.0 0.0.0.0 0 0

nat (dmz) 0 0.0.0.0 0.0.0.0 0 0

static (dmz,outside) (same ip used for mapping ) netmask 255.255.255.255 0 0

access-group 102 in interface outside

(in the dmz x.x.x.x is the email server which users are accessing it from inside and outside network)

Problem Description :- I want to block 6 IPs which are 10.5.2.2 and from 10.5.2.4 to 10.5.2.8 to go over the internet (i want them to access email in dmz). Please tell me how can i block them by adding which commands in the current config . Because i had treid to add deny statements at the end of the access-list but still these IPs are able to go over the internet and if i apply access-group 150 inside everything stops to go over the internet .

3 REPLIES

Re: PIX EXPERTS PLEASE CHECK THIS CONFIG AND HELP ME OUT

I understand your requirement to be allow those 6 hosts only access an email server on your DMZ, deny them access anywhere else, and allow everyone else access everywhere.

Try:

access-group 101 in interface inside

access-list 101 permit tcp host 10.5.2.2 x.x.x.x 255.255.255.240 eq smtp (where x.x.x.x is your dmz network or email server)

access-list 101 permit tcp host 10.5.2.4 x.x.x.x 255.255.255.240 eq smtp

access-list 101 permit tcp host 10.5.2.5 x.x.x.x 255.255.255.240 eq smtp

access-list 101 permit tcp host 10.5.2.6 x.x.x.x 255.255.255.240 eq smtp

access-list 101 permit tcp host 10.5.2.7 x.x.x.x 255.255.255.240 eq smtp

access-list 101 permit tcp host 10.5.2.8 x.x.x.x 255.255.255.240 eq smtp

access-list 101 deny ip host 10.5.2.2 any

access-list 101 deny ip host 10.5.2.4 any

access-list 101 deny ip host 10.5.2.5 any

access-list 101 deny ip host 10.5.2.6 any

access-list 101 deny ip host 10.5.2.7 any

access-list 101 deny ip host 10.5.2.8 any

access-list 101 permit ip any any

Hope it helps.

Steve

Re: PIX EXPERTS PLEASE CHECK THIS CONFIG AND HELP ME OUT

Hi,

clear the current access-list 150:

no access-list 150

If you only want to block outside access for the 6 specific IPaddresses and allow everything else from inside to outside and dmz, then this ACL commands will do:

access-list 150 deny ip host 10.5.2.2 any

access-list 150 deny ip host 10.5.2.4 any

access-list 150 deny ip host 10.5.2.5 any

access-list 150 deny ip host 10.5.2.6 any

access-list 150 deny ip host 10.5.2.7 any

access-list 150 deny ip host 10.5.2.8 any

access-list 150 permit ip any any

access-list 150 permit icmp any any

access-group 150 in interface inside

Access-lists are always processed from top to buttom. The processing stops once a match is found. If no match is found in the ACL, the traffic is denied by default.

Kind Regards,

Tom

Community Member

Re: PIX EXPERTS PLEASE CHECK THIS CONFIG AND HELP ME OUT

thanks for your help but access-list 150 is been used by nat command . Please check the nat command also. i had tried adding these commands in the current access-lists but if i apply that access-list to inside interface it stops everything . I think so it is blocking because of access-list 150 which is been used by nat command

111
Views
0
Helpful
3
Replies
CreatePlease to create content