Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

Pix501 ComSettings?

I just wonder which com-settings I should use in hyperterminal when I download my config-file through

Com1 on my laptop.

Must I do a reset of the pix before I download the new config-file? And how do I do that?

Kindly, Jorgen Fransson

2 REPLIES
Silver

Re: Pix501 ComSettings?

9600, data bits 8, no parity, stop bits 1, flow control hardware.

you can do a write terminal in your comm session, and cut and paste the file to notepad.

you might want to reset the pix before you download the config file, but it depends on how you want to do things.

clear config should wipe the current pix config, but not what is on flash. so if you do a clear config, and then cut and paste in the new config to hyperterminal, and then write memory, you will have changed the running config and saved it

Community Member

Re: Pix501 ComSettings?

Thank you for your quick response!

Do you you think I must reset my pix?

Or can I just paste the new file in hyperterminal

and choose "paste to host"?

This is the old config-file:

PIX Version 6.3(1)

interface ethernet0 auto

interface ethernet1 100full

nameif ethernet0 outside security0

nameif ethernet1 inside security100

enable password xxxxxxxxxxxxxxxx encrypted

passwd xxxxxxxxxxxxxxxx encrypted

hostname xxxxxxxxx

fixup protocol ftp 21

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol http 80

fixup protocol ils 389

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol sip 5060

fixup protocol sip udp 5060

fixup protocol skinny 2000

fixup protocol smtp 25

fixup protocol sqlnet 1521

names

pager lines 24

mtu outside 1500

mtu inside 1500

ip address outside dhcp setroute

ip address inside 192.168.100.254 255.255.255.0

ip audit info action alarm

ip audit attack action alarm

pdm history enable

arp timeout 14400

global (outside) 1 interface

nat (inside) 1 0.0.0.0 0.0.0.0 0 0

timeout xlate 1:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00

timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00

timeout uauth 0:05:00 absolute

aaa-server TACACS+ protocol tacacs+

aaa-server RADIUS protocol radius

aaa-server LOCAL protocol local

no snmp-server location

no snmp-server contact

snmp-server community public

no snmp-server enable traps

floodguard enable

telnet timeout 5

ssh timeout 5

console timeout 0

dhcpd address 192.168.100.200-192.168.100.220 inside

dhcpd lease 3600

dhcpd ping_timeout 750

dhcpd auto_config outside

dhcpd enable inside

terminal width 80

conduit permit icmp any any

And this is the new config-file:

PIX Version 6.3(1)

interface ethernet0 auto

interface ethernet1 100full

nameif ethernet0 outside security0

nameif ethernet1 inside security100

enable password xxxxxxxxxxxxxxxx encrypted

passwd xxxxxxxxxxxxxxxx encrypted

hostname xxxxxxxxx

fixup protocol ftp 21

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol http 80

fixup protocol ils 389

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol sip 5060

fixup protocol sip udp 5060

fixup protocol skinny 2000

fixup protocol smtp 25

fixup protocol sqlnet 1521

names

pager lines 24

mtu outside 1500

mtu inside 1500

ip address outside dhcp setroute

ip address inside 192.168.100.254 255.255.255.0

ip audit info action alarm

ip audit attack action alarm

pdm history enable

arp timeout 14400

global (outside) 1 interface

nat (inside) 1 0.0.0.0 0.0.0.0 0 0

timeout xlate 1:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00

timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00

timeout uauth 0:05:00 absolute

aaa-server TACACS+ protocol tacacs+

aaa-server RADIUS protocol radius

aaa-server LOCAL protocol local

no snmp-server location

no snmp-server contact

snmp-server community public

no snmp-server enable traps

floodguard enable

telnet timeout 5

ssh timeout 5

console timeout 0

dhcpd address 192.168.100.200-192.168.100.220 inside

dhcpd lease 3600

dhcpd ping_timeout 750

dhcpd auto_config outside

dhcpd enable inside

terminal width 80

conduit permit icmp any any

pcanywhere-status UDP 5632

pcanywhere-data TCP 5631

The only thing that is changed is the two last rows.

I need to open up to ports to allow PcAnywhere to

run through the pix. Thats all I want to do...

Kindly, Jorgen Fransson

86
Views
0
Helpful
2
Replies
CreatePlease to create content