Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Cisco Support Community site will be in read only mode on Dec14, 2017 from 12:01am PST to 11:30am for standard maintenance. Sorry for the inconvenience.

New Member

Problem connecting networks?help?

I want to connect my LAN to two remote offices in Dallas and Texas. I have two routers one for each office connected with T1 lines.Now I want to put the one PIX515e between my LAN to Dallas and Texas before both routers.So I have 3 ethernet interfaces. One connected with LAN switch, 2nd with Dallas router's ethernet and 3rd with Texas router's ethernet.following is the output of my PIX's sh run..

interface ethernet0 auto

interface ethernet1 auto

interface ethernet2 auto

nameif ethernet0 dallas security0

nameif ethernet1 inside security100

nameif ethernet2 texas security40

enable password xxxx

passwd xxxx

hostname xxxxxxxxx

fixup protocol dns maximum-length 512

fixup protocol ftp 21

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol http 80

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol sip 5060

fixup protocol sip udp 5060

fixup protocol skinny 2000

fixup protocol smtp 25

fixup protocol sqlnet 1521

fixup protocol tftp 69

names

access-list acl_out permit ip any any

pager lines 24

icmp permit any dallas

icmp permit any inside

mtu dallas 1500

mtu inside 1500

mtu texas 1500

ip address dallas 172.26.29.2 255.255.255.0

ip address inside 172.26.22.10 255.255.255.0

ip address texas 10.46.46.2 255.255.255.0

ip verify reverse-path interface dallas

ip verify reverse-path interface inside

ip audit info action alarm

ip audit attack action alarm

pdm logging informational 100

pdm history enable

arp timeout 14400

global (dallas) 1 172.26.29.10-172.26.29.50 netmask 255.255.255.0

global (dallas) 1 172.26.29.9 netmask 255.255.255.0

global (texas) 1 10.46.46.10-10.46.46.50 netmask 255.255.255.0

global (texas) 1 10.46.46.9

nat (inside) 1 0.0.0.0 0.0.0.0 0 0

access-group acl_out in interface dallas

access-group acl_out in interface inside

access-group acl_out in interface texas

route texas 10.2.1.0 255.255.255.0 10.46.46.1 1

route dallas 150.100.0.0 255.255.0.0 172.26.29.1 1

route dallas 192.168.30.0 255.255.255.0 172.26.29.1 1

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00

timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00

timeout uauth 0:05:00 absolute

aaa-server TACACS+ protocol tacacs+

aaa-server TACACS+ max-failed-attempts 3

aaa-server TACACS+ deadtime 10

aaa-server RADIUS protocol radius

aaa-server RADIUS max-failed-attempts 3

aaa-server RADIUS deadtime 10

aaa-server LOCAL protocol local

http server enable

http 192.168.1.0 255.255.255.0 inside

no snmp-server location

no snmp-server contact

snmp-server community public

no snmp-server enable traps

floodguard enable

telnet 172.26.22.0 255.255.255.0 inside

telnet timeout 5

ssh timeout 5

console timeout 0

dhcpd lease 3600

dhcpd ping_timeout 750

terminal width 80

Cryptochecksum:xxxx

: end

But from my LAN side I am totally unable to connect with both offices... from within the PIX I can ping remote office computers but not from LAN computers... Help me out please.

7 REPLIES
Silver

Re: Problem connecting networks?help?

I uploaded your config to a pix and from the inside was able to ping and telnet to the dallas router. This is a good indication I should be able to reach clients beyond that. As long as the rest of the network is working correctly.

You may want to do some trace routes from the inside to the other networks and from the other networks to the inside. Verify you have routes coming back from those internal networks as well.

New Member

Re: Problem connecting networks?help?

On Dallas and texas network routers, there are route to my dallas and texas interface network IDs.I think there is no need for the route to my internal network ID because NAT is enabled.Am I right or wrong?

Silver

Re: Problem connecting networks?help?

right.

Turn on logging on the pix. Do trace route and pings from both sides and if traffic is being denied you will see it in the loggs. If your not getting any denies you may want to capture traffic on the pix interfaces to see if the requests and/or reply's are acutally getting to the pix.

New Member

Re: Problem connecting networks?help?

I tried to use logging on command. But there is nothing display on console window. Can you tell me the command with witch I can monitor passed and denied traffic from my PIX firewall?

New Member

Re: Problem connecting networks?help?

I want to know the command which will enable logging for only denied or passed traffic from a particular source or to a specific destination for inside and outside....on PIX515e

Silver

Re: Problem connecting networks?help?

logging on

logging console errors (connected via console cable)

logging monitor errors (connected via telnet/ssh, must also enable terminal monitor)

logging trap errors

logging host inside IP_ADDRESS (log to syslog on inside)

Link on how to capture:

http://www.cisco.com/en/US/customer/products/sw/secursw/ps2120/products_configuration_guide_chapter09186a0080172797.html#wp1038055

New Member

Re: Problem connecting networks?help?

This is just a useless reply but the last time I checked Dallas was in Texas :)

176
Views
3
Helpful
7
Replies
CreatePlease to create content