Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

VPN-QoS over MPLS

We are facing a mpls-backbone with vpns. Our customer requires that these vpns get guaranteed bandwidth. We have found a lot of information about VPN-QoS over MPLS but no configuration examples. Could you please tell us how to configure such a requirement?

7 REPLIES
Bronze

Re: VPN-QoS over MPLS

Check out this webpage…..It’s a great place to start: http://www.cisco.com/warp/public/cc/so/neso/vpn/vpnsp/mpls_wi.htm

Here is a configuration I found as well: http://www.cisco.com/warp/partner/synchronicd/cc/pd/si/ig8400/prodlit/igxm_rg.htm

You might want to get some help the first time you do it, because it’s rather tedious the first time through.

New Member

Re: VPN-QoS over MPLS

I am in the same boat here. I am looking to to push traffic across TE-tunnels with explicit paths from particular VPNs using RSVP signalling to build bandwidth guarantees, but it seems that since the tunnels are using the BGP next hop to determine which path to use when forwarding traffic, I can't make traffic take any explicit path since the actual destination of the tunnel is not in the main RIB.

This seems to work fine when the destination appears in the main routing table, but the minute you push the network into a VRF the router only has the MpBGP next-hop address to use (since you can't make the tunnel examine the VRF RIB), which is reachable through 3 different directions in my topology...

Are there any configuration examples available showing how to build path selection using VPNs and TE-tunnels together? This is an IP-only environment.

New Member

Re: VPN-QoS over MPLS

We offer a number of resources at http://www.cisco.com/tac including configuration examples and white papers. If you are unable to find what you are looking for specifically, please open a case with our technical assistance center for help with this issue. You may open a TAC cas online at http://www.cisco.com/tac/caseopen

If any forum members have some recommendations, please post them to this thread.

Thank you for your inquiry.

New Member

Re: VPN-QoS over MPLS

As well-know,MPLS have 3 applications,VPN,TE,COS.

Several different methods exist for supporting CoS across an MPLS backbone, the choice depending on whether the core has label switch routers (LSRs) or ATMLSRs. However, the CoS building blocks are the same: CAR, WRED, and WFQ.

Cisco has detail configuration manual.If you can't find it.I would like to mail it to you.

New Member

Re: VPN-QoS over MPLS

i do not have details regarding the configuration of the CoS parameters such as CAR,WFQ etc.

Cud u please arrange to provide these details?

New Member

Re: VPN-QoS over MPLS

Hi kunpeng,

Would you please send me the detailed configuration manual by mail?

Thank very much!

Yi

New Member

Re: VPN-QoS over MPLS

There are 2 doc. on CCO:

MPLS CoS over ATM: Multi-VC TBR (using CAR)

http://www.cisco.com/warp/customer/121/mpls_cos_atm.html

MPLS CoS over ATM: CoS Map

http://www.cisco.com/warp/customer/121/mpls_cosmap.html

Alternatively You can use our product ( Orchestream) witch will config Cisco router to do MPLS, MPLS/VPN and QoS.

see www.orchestream.com

Roumen Doukov

___________________________________________________________________________

Senior Technical Consultant

T: +44 (0)20 7348 1537 M: +44 (0)7890709417

Orchestream

Avon House, Kensington Village, Avonmore Road, London W14 8TS

T: +44 (0)20 7348 1500 F: +44 (0)20 7348 1501

www.orchestream.com

http://www.orchestream.com

202
Views
0
Helpful
7
Replies
CreatePlease login to create content