Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 

ASR 1002-X, IOS XE and ISG

Hello All.

I started using asr 1002-x with IOS XE instead of 7201 as ISG + AAA + RADIUS.

I had a question on IOS XE 3.11, 3.10, 3.9.

Command "radius-server vsa send ..."  is in a configuration, however it isn't applied and doesn't appear in running-config.

cod-r8(config)#radius-server vsa send?

  accounting Send in accounting requests

  authentication Send in access requests

  cisco-nas-port Send cisco-nas-port VSA (2)

  <cr>

cod-r8(config)#radius-server vsa send accounting 

cod-r8(config)#radius-server vsa send authentication           

cod-r8(config)#radius-server vsa send cisco-nas-port

cod-r8(config)#do sh run | include vsa

radius-server vsa send cisco-nas-port</cr>

It turns out that vsa is included by default or doesn't work at all?

Thanks.

_________

Konstantin

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

ASR 1002-X, IOS XE and ISG

Hi Konstantin,

I believe those commands are enable by default and that's why theey are not dispayed when doing 'show run'. I checked on one device running 3.10.1 and, when using 'show run all', I can see the commands:

bsns-asr1002x-1#sh run | in vsa

radius-server vsa send cisco-nas-port

bsns-asr1002x-1#sh run all | in vsa

radius-server vsa send cisco-nas-port

radius-server vsa send accounting

radius-server vsa send authentication

bsns-asr1002x-1#

Regards.

4 REPLIES
Cisco Employee

ASR 1002-X, IOS XE and ISG

Hi Konstantin,

I believe those commands are enable by default and that's why theey are not dispayed when doing 'show run'. I checked on one device running 3.10.1 and, when using 'show run all', I can see the commands:

bsns-asr1002x-1#sh run | in vsa

radius-server vsa send cisco-nas-port

bsns-asr1002x-1#sh run all | in vsa

radius-server vsa send cisco-nas-port

radius-server vsa send accounting

radius-server vsa send authentication

bsns-asr1002x-1#

Regards.

ASR 1002-X, IOS XE and ISG

Hi Manuel,

Thanks for your answer.

It is strange that these commands cleaned from sh run view.

I see you in a network have asr 1002-x.

To what ios you will advise for ISG + IPoE?

Thanks.

_________

Konstantin

Cisco Employee

ASR 1002-X, IOS XE and ISG

Hi Konstantin,

Regarding "It is strange that these commands cleaned from sh run view.": this is normal for many default configuration commands.

Mine is a lab device so I cannot really comment on stability or provide you a recommendation based on that. However, I see that the download section from Cisco.com mentiones the following release as the recommended based on quality, stability and longevity:

asr1002x-universal.03.07.04a.S.152-4.S4a.SPA.bin

The best would be for you to check this with yor cisco Account Team or Advanced Services Team as normally they are the proper point of contacts for SW advisory.

Regards.

New Member

ASR 1002-X, IOS XE and ISG

Hi Konstantin,

we observed that 3.10.1 were more stable in our environment than 3.11. We have made a rollback to 3.10.1 after two strange faults that we couldn't reproduce again. However we use asr1000, not asr1000-x

579
Views
0
Helpful
4
Replies
CreatePlease to create content