Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

PRE5 / SCH1 - SPA problem

Hi all ,

 

I have ubr10k with IOS SCH1 , and PRE5 installed .

 

In chassis is SIP-600 with 3G SPA in bay 1/0 and all 3 port are connected to rfgw and working fine  as 1GE .

 

second 3G SPA in bay 1/1 is not working . connected port gi 1/1/2 to same rfgw ( 4th port ) as first SPA , and communication between gi 1/1/2 and 4th port in rfgw is not working .

on gi 1/1/2 is configured ip ,and also on 4th port of rfgw is configured ip but cant ping rfgw from cmts  . ( from all 3 port on SPA bay 1/0 i can ping ) 

output from cmts :

 

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.200.62, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
#ping 192.168.200.61         <<--- IP on 4th port of rfgw 

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.200.61, timeout is 2 seconds:
.....

Success rate is 0 percent (0/5)
#sh int gi 1/1/2
GigabitEthernet1/1/2 is up, line protocol is up 
  Hardware is Half-height Gigabit Ethernet MAC Controller, address is bc16.6527.2617 (bia bc16.6527.2617)
  Internet address is 192.168.200.62/30
  MTU 1500 bytes, BW 10000 Kbit, DLY 10 usec, 
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full Duplex, 1000Mbps, link type is auto, media type is unknown media type
  output flow-control is unsupported, input flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:09, output 00:00:01, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Interface GigabitEthernet1/1/2 queueing strategy: PXF Class-based
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     220 packets input, 24913 bytes
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     1192 packets output, 231155 bytes
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 pause output
     0 output buffer failures, 0 output buffers swapped out

#sh ip arp  gi 1/1/2
Protocol  Address          Age (min)  Hardware Addr   Type   Interface
Internet  192.168.200.62          -   bc16.6527.2617  ARPA   GigabitEthernet1/1/2
Internet  192.168.200.61          0   38c8.5c2c.85be  ARPA   GigabitEthernet1/1/2

 

Changing SFP on cmts and rfgw didint help . 

 

Thanks 

VZ

1 REPLY
New Member

Does on CMTS with standby

Does on CMTS with standby PRE5 , 10GE port  on standby PRE5 can work independent from activ PRE5 10GE port ?

 

KR 

39
Views
0
Helpful
1
Replies