Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

SPA-4XT-SERIAL Installation Issue on 6513- Error # %SPA_OIR-3-UNSUPPORTED

I have installed the 7600-SIP-200 and SPA-4XT-SERIAL modules in the 6513 switch. Both modules have been detected. But, I received following error message:

“SLOT 1: 00:00:04: %SPA_OIR-3-UNSUPPORTED: The SPA-4XT-SERIAL in Subslot 0 is not supported by the SIP-200 module”

I had upgraded the IOS and had also changed the slot but still the same issue.

When I checked the Cisco documentation for 6500 switch, it says that it supports 7600-SIP-200 and SPA-4XT-SERIAL modules. "show module" of the router is as follows:

MOFWAN-6513#sh module

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1    0  4-subslot SPA Interface Processor-200  7600-SIP-200       JAE1322APKW

  2    0  2-subslot Services SPA Carrier-400     7600-SSC-400       JAE13198KBI

  3    6  Firewall Module                        WS-SVC-FWM-1       SAD1320016W

  5   48  SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX     SAL1315N14R

  7    2  Supervisor Engine 720 (Hot)            WS-SUP720-3B       SAL1303GP73

  8    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL1327TC69

10   24  CEF720 24 port 1000mb SFP              WS-X6724-SFP       SAL1315MXX0

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  1  0025.84e0.b5c0 to 0025.84e0.b5ff   2.303 12.2(33)SXH6 12.2(33)SXH6 Ok

  2  0023.04e2.9eb8 to 0023.04e2.9ef7   2.0   12.2(33)SXH6 12.2(33)SXH6 Ok

  3  0024.9773.e760 to 0024.9773.e767   4.5   7.2(1)       4.0(8)       Ok

  5  0025.4551.84c8 to 0025.4551.84f7  11.3   7.2(1)       8.7(0.22)BUB Ok

  7  001a.a22d.6c2c to 001a.a22d.6c2f   5.7   8.5(2)       12.2(33)SXH6 Ok

  8  0024.1499.535c to 0024.1499.535f   5.9   8.5(3)       12.2(33)SXH6 Ok

10  0024.c481.5ac0 to 0024.c481.5ad7   3.3   12.2(18r)S1  12.2(33)SXH6 Ok

Mod  Sub-Module                  Model              Serial       Hw     Status

---- --------------------------- ------------------ ----------- ------- -------

1/0                             SPA-4XT-SERIAL     JAE14080NGQ  2.0    AdmnDown

1/1                             SPA-4XT-SERIAL     JAE14080NH2  2.0    OutSrvc

2/0                             SPA-IPSEC-2G       JAE1332FXKP  2.0    OutSrvc

  7  Policy Feature Card 3       WS-F6K-PFC3B       SAL1303GMBR  2.4    Ok

  7  MSFC3 Daughterboard         WS-SUP720          SAL1303GKV0  3.2    Ok

  8  Policy Feature Card 3       WS-F6K-PFC3B       SAL1327TC0G  2.5    Ok

  8  MSFC3 Daughterboard         WS-SUP720          SAL1327T8E3  4.0    Ok

10  Distributed Forwarding Card WS-F6700-DFC3C     SAL1322R0K4  1.2    Ok

Mod  Online Diag Status

---- -------------------

  1  Pass

1/0 Not Applicable

1/1 Not Applicable

  2  Pass

2/0 Not Applicable

  3  Pass

  5  Pass

  7  Pass

  8  Pass

10  Pass

Please let me know what could be the possible issue?

1 REPLY
Hall of Fame Super Silver

Re: SPA-4XT-SERIAL Installation Issue on 6513- Error # %SPA_OIR-

Answered in WAN forum

Jerry confirmed this specific SPA is not accepted on C6500 chassis

Best Regards

Giuseppe

566
Views
0
Helpful
1
Replies