Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

02#Aironet 1600 (AIR-CAP1602i) & 3850 WLC (WS-C3850-24T-L)

Hi Friends

Finally join and register 1602i (AIR-CAP1602i-E-k9) to 3850 (WS-C3850-24T) WLC  indecision

Now connect registered 1602i to WS-C2960-24PC-L that C2960 & C3850 trunk together, but again the 1602i not join ! (log below)

When Connect access port of two devices (C2960 & C3850) together and 1602i connect to another access port of C2960, 1602i join & registered !

Really can't use Aps in another branch far from C3850 WLC ?!

 

AP1602i#

*Jun 15 05:03:51.566: %CAPWAP-3-ERRORLOG: Selected MWAR 'Ctrl1'(index 0).
*Jun 15 05:03:51.566: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jun 15 05:03:51.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.188.22 peer_port: 5246
*Jun 15 05:03:51.291: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.188.22 peer_port: 5246
*Jun 15 05:03:51.291: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.188.22

*Jun 15 05:04:09.663: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceed., 1)x(UNKNOWN_MESSAGE_TYPE (5)
*Jun 15 05:04:09.663: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Jun 15 05:04:09.663: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.188.22:5246
*Jun 15 05:04:09.715: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Jun 15 05:04:09.739: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Jun 15 05:04:09.739: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Jun 15 05:04:09.743: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up

*Jun 15 05:04:09.779: %CAPWAP-3-STATIC_TO_DHCP_IP: Could not discover WLC using static IP. Forcing AP to use DHCP.
*Jun 15 05:04:09.795: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up

*Jun 15 05:04:10.743: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jun 15 05:04:10.775: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Jun 15 05:04:10.783: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Jun 15 05:04:11.767: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jun 15 05:04:11.775: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Jun 15 05:04:11.807: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up

*Jun 15 05:04:11.815: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Jun 15 05:04:11.823: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jun 15 05:04:12.807: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Jun 15 05:04:12.815: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jun 15 05:04:12.859: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up

*Jun 15 05:04:13.859: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up

C3850#

Jun 15 05:02:03.631: *%LWAPP-3-VALIDATE_ERR: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  c0:25:5c:96:90:e0

*Jun 15 05:02:03.632: %CAPWAP-3-AP_PORT_CFG: AP connected port Gi1/0/24 is not an access port.

*Jun 15 05:02:03.634: *%LOG-3-Q_IND: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  c0:25:5c:96:90:e0

*Jun 15 05:02:03.634: *%CAPWAP-3-DATA_TUNNEL_CREATE_ERR2: 1 wcm:  Failed to create CAPWAP data tunnel with interface id: 0xf584c00000000b for AP: c025.5c96.90e0 Error Reason: Capwap Data Tunnel create retry exceeded max retry count.

*Jun 15 05:02:21.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination

*Jun 15 05:02:31.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 4 times/sec!.]

*Jun 15 05:02:41.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 2 times/sec!.]

*Jun 15 05:02:51.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 4 times/sec!.]

*Jun 15 05:03:01.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 2 times/sec!.]

*Jun 15 05:03:11.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 4 times/sec!.]

*Jun 15 05:03:21.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 2 times/sec!.]

*Jun 15 05:03:31.755: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 4 times/sec!.]

*Jun 15 05:03:32.590: *%LOG-3-Q_IND: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination

*Jun 15 05:03:32.591: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event () and state (CAPWAP Join Response) combination

*Jun 15 05:03:41.754: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination

*Jun 15 05:04:02.419: *%LOG-3-Q_IND: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination[...It occurred 3 times.!]

*Jun 15 05:04:02.419: *%LWAPP-3-VALIDATE_ERR: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  c0:25:5c:96:90:e0

*Jun 15 05:04:02.420: %CAPWAP-3-AP_PORT_CFG: AP connected port Gi1/0/24 is not an access port.

*Jun 15 05:04:02.420: *%LOG-3-Q_IND: 1 wcm:  Validation of SPAM Vendor Specific Payload failed - AP  c0:25:5c:96:90:e0

*Jun 15 05:04:02.421: *%CAPWAP-3-DATA_TUNNEL_CREATE_ERR2: 1 wcm:  Failed to create CAPWAP data tunnel with interface id: 0xcbe4000000000c for AP: c025.5c96.90e0 Error Reason: Capwap Data Tunnel create retry exceeded max retry count.

*Jun 15 05:04:20.545: *%CAPWAP-3-INVALID_STATE_EVENT: 1 wcm:  Invalid AP event (CAPWAP Discovery Request) and state (CAPWAP Join Response) combination

 

1 ACCEPTED SOLUTION

Accepted Solutions
VIP Purple

Hi,Yes, APs must be directly

Hi,

Yes, APs must be directly connected to the 3850 for it to work in MA or MC mode.Now better to use 3850 switch only for wired network and  better to buy 5500 series WLC then you can use Hreap/flex-connect to connect several branch.

H-REAP Modes of Operation Configuration Example

http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/81680-hreap-modes.html

H-Reap Design and Deployment Guide

http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/71250-h-reap-design-deploy.html

 

Regards

Dont forget to rate helpful posts

5 REPLIES
Hall of Fame Super Gold

Now connect registered 1602i

Now connect registered 1602i to WS-C2960-24PC-L that C2960 & C3850 trunk together, but again the 1602i not join !

Won't work.  The AP has to be DIRECTLY-CONNECTED to the 3850 switch.

New Member

Dear Leo ...I bought several

Dear Leo ...

I bought several AP1206i & one 3850 for several branch. What do i do?sad

VIP Purple

Hi,Yes, APs must be directly

Hi,

Yes, APs must be directly connected to the 3850 for it to work in MA or MC mode.Now better to use 3850 switch only for wired network and  better to buy 5500 series WLC then you can use Hreap/flex-connect to connect several branch.

H-REAP Modes of Operation Configuration Example

http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/81680-hreap-modes.html

H-Reap Design and Deployment Guide

http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/71250-h-reap-design-deploy.html

 

Regards

Dont forget to rate helpful posts

New Member

Hi Dear Sandeap;Ok, got it

Hi Dear Sandeap;

Ok, got it!

Please help me, please enlightened

Without thinking I bought 3 AIR-CAP1602i & WS-C3850-24T-L whit 50 license !

I Wanted to install APs in different site and install WLC in ISP.

Now pleas say to me exactly what do i do?

What are devices (APs & WLC) have to buy that has useful for expansion?

I have Several campuses that connect to ISP whit Fiber or P2P Wireless & must install AP's in these campuses for students an master's. My Switches C2960 series and most of them have not 802.1Q ...

 

VIP Purple

Air CAP 1602i will  work as

Air CAP 1602i will  work as remote AP in flexconnect.

Yes you can install WLC(Cisco Flex 8500 and 7500, Cisco 5500, 4400, and 2500 Series Controllers) on HQ site.

http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/112042-technote-product-00.html

 

1. For flexconnect you must have a WAN connection from HQ to remote site(I think you have it).

2. Then you can connect AP at remote site and WLC ate main site.

3. Here is the links, how to configure flexconnect:

https://supportforums.cisco.com/document/98646/wireless-lan-flexconnect-configuration-example

http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-2/configuration/guide/cg/cg_flexconnect.html

Hope it helps.

 

Regards

Dont forget to rate helpful posts

519
Views
7
Helpful
5
Replies