Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

3850 MC and 3850 MA

Hello,

I have problem with two 3850, one is controler the other one is agent.

 2 AP connected on the MC  are working and not the AP on the MA.

I can see on the MC that MA is UP :

SR-3850-KPG-TLCA#show wireless mobility ap-list
Number of AP entries in the mobility group : 3
Number of AP entries in the sub-domain     : 3
AP name                           AP radio MAC      Controller IP     Learnt from
--------------------------------------------------------------------------------------
LAP2602-KPG-TLCA                  6c99.8999.c590    10.56.43.246      Self
LAP2602-KPG-PRINTER               6c99.8999.c5c0    10.56.43.246      Self
APb838.6107.2826                  6c99.89a1.d010    10.56.43.244      Mobility Agent

 

The MC see all the AP :

SR-3850-KPG-TLCA#sh wireless mobility ap-list
Number of AP entries in the mobility group : 3
Number of AP entries in the sub-domain     : 3
AP name                           AP radio MAC      Controller IP     Learnt from
--------------------------------------------------------------------------------------
LAP2602-KPG-TLCA                  6c99.8999.c590    10.56.43.246      Self
LAP2602-KPG-PRINTER               6c99.8999.c5c0    10.56.43.246      Self
APb838.6107.2826                  6c99.89a1.d010    10.56.43.244      Mobility Agent
Controller IP     AP Count
----------------------------
10.56.43.244      1
10.56.43.246      2

 

It seems that no SSID is broadcast from the AP APb838.6107.2826 . It's impossible te connect on it.

Here the configuration of MC

wireless mobility controller
wireless mobility controller peer-group KPG
wireless mobility controller peer-group KPG member ip 10.56.43.244 public-ip 10.56.43.244
wireless management interface Vlan2

ap country FR
ap group default-group

 

On the MA :
wireless mobility controller ip 10.56.43.246 public-ip 10.56.43.246
wireless management interface Vlan2
wireless mgmt-via-wireless
ap country FR
ap dot11 24ghz rate RATE_1M mandatory
ap dot11 24ghz rate RATE_2M mandatory
ap dot11 24ghz rate RATE_5_5M mandatory
ap dot11 24ghz rate RATE_6M supported
ap dot11 24ghz rate RATE_9M supported
ap dot11 24ghz rate RATE_11M mandatory
ap dot11 24ghz rate RATE_12M supported
ap dot11 24ghz rate RATE_18M supported
ap dot11 24ghz rate RATE_24M supported
ap dot11 24ghz rate RATE_36M supported
ap dot11 24ghz rate RATE_48M supported
ap dot11 24ghz rate RATE_54M supported
ap dot11 5ghz rate RATE_6M mandatory
ap dot11 5ghz rate RATE_9M supported
ap dot11 5ghz rate RATE_12M mandatory
ap dot11 5ghz rate RATE_18M supported
ap dot11 5ghz rate RATE_24M mandatory
ap dot11 5ghz rate RATE_36M supported
ap dot11 5ghz rate RATE_48M supported
ap dot11 5ghz rate RATE_54M supported
ap group default-group
end

 

Even ap dot11 command are not present on the MC, all is UP and client are connected on AP of MC.

I found this errror :

%IOSXE-7-PLATFORM: 1 process wcm: 6c99.89a1.d010 Ignoring unsupported vendor-specific message 0x00409600-0088-Call AP System Stats Payload from AP 6c99.89a1.d010

 

Do you have ideas on this problem please?

 

Regards,

 

JB

 

 

 

 

 

 

Everyone's tags (1)
4 REPLIES

Refer the discussionhttps:/

Refer the discussion

https://supportforums.cisco.com/discussion/12025486/3850-and-ap-2602i-e-k9-ap-wont-stay-joined

New Member

Hello, Thanks for the link.

Hello,

 

Thanks for the link. The ap is well joined, but no SSID is broadcast.

AP Name                           AP Model  Ethernet MAC    Radio MAC       State
----------------------------------------------------------------------------------------
LAP2602-KPG-TLCA                  2602I     b838.6127.8367  6c99.8999.c590  Registered
 

The 3850 MC see the the AP on the 3850 MA :

SR-3850-KPG-TLCA#sh wireless mobility ap-list
Number of AP entries in the mobility group : 3
Number of AP entries in the sub-domain     : 3

AP name                           AP radio MAC      Controller IP     Learnt from
--------------------------------------------------------------------------------------
LAP2602-KPG-TLCA                  6c99.8999.c590    10.56.43.244      Mobility Agent
LAP2602-KPG-PRINTER               6c99.8999.c5c0    10.56.43.246      Self
APb838.6107.2826                  6c99.89a1.d010    10.56.43.246      Self

Controller IP     AP Count
----------------------------
10.56.43.244      1
10.56.43.246      2

Radio on AP of MA  are UP :

S-3850-KPG-TLCB#sh ap dot11 24ghz summary
AP Name            MAC Address     Slot  Admin State  Oper State  Channel        Width  TxPwr
----------------------------------------------------------------------------------------------
LAP2602-KPG-TLCA   6c99.8999.c590     0  Enabled      Up          11*               20    1(*)

 

I try to swap two AP, one on the MC and MA, the result is the same, the AP of MA stil doesn't broadcast SSID.

 

Regards,

 

JB

 

 

 

 

 

 

Cisco Employee

ps MUST be directly connected

ps MUST be directly connected to 3850 to join a 3850,so what options are you left
with:
1)You can see catalyst 3850 switch model which supports PoE, you can see table in link for
catalyst 3850 switch models supporting PoE:
http://www.cisco.com/en/US/docs/switches/lan/catalyst3850/software/release/3.2_0_se/releas
e_notes/OL28114.html#wp223622

So if  you directly connect the AP to the 3850 switch and your switch model doesn't
support PoE then:

2)You will then need to select an alternate powering option for your AP as shown in table
1 below:
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps12534/data_sheet_c78-709514.h
tml

Powering Options for Cisco AP2600:
� Cisco AP2600 Power Injectors (AIR-PWRINJ4=)
� Cisco AP2600 Local Power Supply (AIR-PWR-B=)

For documentation on Aps must be directly connected to 3850 to join a 3850, you can refer
to link and Q&A section:
 http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps12686/qa_c67-722110.html
http://www.cisco.com/en/US/docs/switches/lan/catalyst3850/software/release/3.2_0_se/releas
e_notes/OL28114.html#wp171441
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps12686/deployment_guide_c07-72
7067.html#wp9000118

--Snip from Q&A-----
Q. Which models of access points can a Cisco Catalyst 3850 switch support?
A. The following models of access points are supported: LAP1040, LAP1142, LAP1260,
CAP3500, CAP3600, CAP2600, and CAP1600.

Q. In what modes can an access point operate when connected to a Cisco Catalyst 3850?
A. The following access point modes are supported on the Cisco Catalyst 3850:

� Local mode

� SE connect mode

� Monitor mode

� Sniffer mode
Flex mode and indoor mesh access points are not supported.

Q. Does the Cisco Catalyst 3850 support indirectly connected access points?
A. No. The Cisco Catalyst 3850 switch will always terminate the CAPWAP tunnel locally.
Pass-through mode or indirectly connected access point is not supported at this time.

Q. In what wireless modes can the Cisco Catalyst 3850 operate?
A. The Cisco Catalyst 3850 Series Switch supports two modes of operation. It can be
operated as a mobility agent or mobility controller.


Once you do have the Aps directly connected to the C3850 with PoE support or are using the
relevant powering option incase you connect your Aps directly to C3850, but your C3850
doesn't support PoE, then your issue will be resolved.
All the config relevant to have a working scenario is also summarised in:
 https://supportforums.cisco.com/docs/DOC-34430
New Member

Hello,Thanks for this answer.

Hello,

Thanks for this answer. The problem was simple. WLAN needed to be created also on the mobilitay agent.

Regards,

 

JB

403
Views
0
Helpful
4
Replies
CreatePlease to create content