Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

802.11n 5@40

I try get all benefits of 802.11n with 1262N in standalone mode (12.4(25d)JA)

But I see the next

Settings for int dot11radio1 is the next

speed  basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.

channel width 40-above

channel 5300

station-role root

All antennas are active, wmm is active

But I get only about 2MB/s by ftp

For test I use the next scheme

Client-Win7(Linksys ae2500)(vlanA) == R1:1262N:Gi0  == Gi:SW:Gi == Gi:(vlanA):FtpServer

On the same stand I get about 6MB/s with 5Ghz and channel width 20MHz

In all attempts was only one client and the clean environment, i proved it with a spectrum-analyzer

Tell me what I'm doing wrong? Thank you.

Client associated with next parameters:

5@40:

----

Key Mgmt type    : WPAv2 PSK         

Encryption       : AES-CCMP

Current Rate     : m15.              

Capability       : WMM 11h

Supported Rates  : 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15

Bandwidth        : 40 MHz 

5@20

---

And the same, but bandwidth  is   20 MHz

Everyone's tags (4)
8 REPLIES
Hall of Fame Super Silver

Re: 802.11n 5@40

Eugene,

What is your baseline with a wired pc doing the same test on vlan A?

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Bronze

802.11n 5@40

The supported rates is not important. Those are for a/b/g. What you have to verify is if High Throughput(HT) is enabled with the MCS rates 0-7 for clients and 8-15 for AP.

New Member

Re: 802.11n 5@40

Scott,

with a wired pc I get 20-25MB/s

ftp:gi - sw - gi:notebook and ftp:gi - gi:notebook

802.11n 5@40

Have you tried different client for testing?

This link could be helpful:  http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a0080a3443f.shtml#topic8

HTH

Amjad

Rating useful replies is more useful than saying "Thank you"
Bronze

802.11n 5@40

Eugene,

What guard interval is set, 400ns or 800ns or only 800ns? 400ns ensures higher throughput than 800ns.

To be sure, enter the command

interface dot11radio 1 --------- 5GHz n radio

guard interval any

New Member

Re: 802.11n 5@40

"guard interval any"     is default setting

sh controllers dot11Radio 1 | i Guard

Guard-Interval: Any

In any case, I attach the full version of sh controll dot11radio1

Maybe this is  will help to understand what I am missing

New Member

Re: 802.11n 5@40

Сolleagues, the problem with the adapter.

Dlink dwa-160 rev A2 managed to get about 11MB/s

AE2500 is still not working as it should be.

Surprised that Linksys is such a bad product.

May be possible to configure the adapter,

but after all that time that I spent I very doubt.

Thanks all for replies

Hall of Fame Super Silver

802.11n 5@40

Eugene,

It is always a good idea to baseline from the wired side, so you can get an idea of the actual throughput from the devices you are using, and you can figure out the percentage of actual throughput if the ftp was connected to a 100mbps or 1000mbps connection.  Using multiple adapter as a test is also good, because each one has it good and bad.  At least you were able to see that in your testing.

-Scott
*** Please rate helpful posts ***
661
Views
0
Helpful
8
Replies