12-04-2002 03:17 AM - edited 07-04-2021 08:23 AM
We have several aironet devices. We are an ISP, and we don't have wireless solution engine, but we have to upgrade firmware in several device:Bridges,acces points, workgroup bridges. I read an snmp OID which I can tell the device to upgrade firmware. Only I have to set the default file server, and maybe the default image name in the aironet devices. I can ' t find this document. Is there anybody help me?
Thanks in advance
12-09-2002 10:27 AM
Here is a URL that has pretty much all the useful information that you need for the Aironet devices. http://www.cisco.com/univercd/cc/td/doc/product/wireless/index.htm
01-02-2003 02:51 PM
hello
" I read an snmp OID which I can tell the device to upgrade firmware. "
could you share the SNMP OID. I tried browing the MIB and I could not find the value.
I would set the ip addr of the TFTP server and the file name in the config file of the APs and just use the snmp oid to trigger them to upgrade
01-06-2003 01:53 AM
Hello !
MIB: awcVx
To load firmware from file server:
OID: awcFileXferCmdInvokeFileLoad value: 'start'
status for load:
OID: awcFileXferCmdStatusFileLoad
value:
0 = Operation completed successfully
(or has not taken place).
2 = At least one file was not found on
the file server.
12 = Insufficient memory to load all
files.
22 = No file specified, or invalid file
format.
35 = File format of at least one of the
files is not supported.
68 = Operation is still in progress.
Poll again later.
72 = Operation was started, but later was
canceled."
To save firmware to file server:
OID: awcFileXferCmdInvokeFileSave value: 'start'
status for save:
OID: awcFileXferCmdStatusFileSave
value:
0 = Operation completed successfully (or
has not taken place).
1 = Insufficient permission to save the
files.
2 = A directory specified for saving at
least one of the files was not found.
22 = No file specified, or invalid file
format.
68 = Operation is still in progress.
Poll again later.
72 = Operation was started, but later was
canceled."
I think it helps you. I tried these with AP1200 and it works!
03-21-2003 11:34 PM
Hello SZILARD,
Thank you for the reply. After you have sent me the above OIDs, I have tired to work with it. I am using ucd-snmp package. As a test I trried to up load the current image to the tftp server on a AP1200. I used the following command
snmpset 192.168.0.10 -c private awcFileXferCmdInvokeFileSave value: 'start'
The above command gives a error. Please suggest how should I use it ?
I am mainly interested in the procedure to load firmware in APs.
How do I specify the image file ?
Thank you.
03-24-2003 06:12 AM
what is the error ?
03-24-2003 01:52 PM
Hello,
When I use the following command
\usr\bin>snmpset 192.168.0.10 -c private awcFileXferCmdInvokeFileSave value: 'start'
The error that shows up is
'start': Needs type and value
I have downloaded the MIB file from cisco and copied it to the main mib location used by ucd-snmp package.
03-25-2003 04:12 AM
Hi !
The syntax is :
snmpset ipaddr community snmp-object type value
for example:
snmpset 172.16.11.2 public .1.3.6.1.4.1.522.3.4.7.0 i 2
snmp-object: awcFileXferCmdInvokeFileSave (OID: 1.3.6.1.4.1.522.3.4.7)
i: integer type
integer type 2 =start
good luck
szicsu
03-26-2003 11:22 AM
Hello Szicsu,
Thank you very much for the OIDs.
Amit
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: