Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

AP-1041N LWAPP reboot in a loop

Hi all!

We have a few AIR-LAP1041N-E-K9 and 2106 controller. One of the 1041N began rebooting in a loop. All over AP work fine.

This morning, AP normally loaded at once. Two hours later, after AP reboot, situation repeated itself.

Output from console:

using  eeprom values

WRDTR,CLKTR: 0x85000800 0xc0000000

RQDC ,RFDC : 0x80000037 0x0000018c

using ЪЪЪЪ ddr static values from serial eeprom

ddr init done

Running Normal Memtest...

Passed.

IOS Bootloader - Starting system.

FLASH CHIP:  Numonyx P33

Checking for Over Erased blocks

......................................................................................................................................................................................................................................................

Xmodem file system is available.

DDR values used from system serial eeprom.

WRDTR,CLKTR: 0x85000800, 0xc0000000

RQDC, RFDC : 0x80000037, 0x0000018c

Error resetting PCI Express phy on port 0

PCIE0 port 0 not initialized

PCIE1: link is NOT up.

PCIE1 port 1 not initialized

PCIEx: initialization done

flashfs[0]: 27 files, 8 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 32385024

flashfs[0]: Bytes used: 7364096

flashfs[0]: Bytes available: 25020928

flashfs[0]: flashfs fsck took 27 seconds.

Reading cookie from system serial eeprom...Done

Base Ethernet MAC address: 70:81:05:ec:45:70

Ethernet speed is 100 Mb - FULL duplex

Loading "flash:/c1140-k9w8-mx.124-23c.JA3/c1140-k9w8-mx.124-23c.JA3"...#############....

File "flash:/c1140-k9w8-mx.124-23c.JA3/c1140-k9w8-mx.124-23c.JA3" uncompressed and installed, entry point: 0x4000

executing...

enet halted

Proceeding with system init

Proceeding to unmask interrupts

Initializing flashfs...

FLASH CHIP:  Numonyx P33

Checking for Over Erased blocks

......................................................................................................................................................................................................................................................

flashfs[1]: 27 files, 8 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 32126976

flashfs[1]: Bytes used: 7364096

flashfs[1]: Bytes available: 24762880

flashfs[1]: flashfs fsck took 7 seconds.

flashfs[1]: Initialization complete.

flashfs[2]: 0 files, 1 directories

flashfs[2]: 0 orphaned files, 0 orphaned directories

flashfs[2]: Total bytes: 11999232

flashfs[2]: Bytes used: 1024

flashfs[2]: Bytes available: 11998208

flashfs[2]: flashfs fsck took 1 seconds.

flashfs[2]: Initialization complete....done Initializing flashfs.

Ethernet speed is 100 Mb - FULL duplex

Radio0 not present 0 0 0 0 0 B

Radio1 not present 0 0 0 0 0 0

cisco AIR-LAP1041N-E-K9    (PowerPC405ex) processor (revision A0) with 98294K/32768K bytes of memory.

Processor board ID FCZ1537Z0QF

PowerPC405ex CPU at 333Mhz, revision number 0x147E

Last reset from power-on

LWAPP image version 7.0.220.0

1 Gigabit Ethernet interface

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 70:81:05:EC:45:70

Part Number                          : 73-14034-03

PCA Assembly Number                  : 800-34273-04

PCA Revision Number                  : A0

PCB Serial Number                    : FOC153176ET

Top Assembly Part Number             : 800-34284-02

Top Assembly Serial Number           : FCZ1537Z0QF

Top Revision Number                  : A0

Product/Model Number                 : AIR-LAP1041N-E-K9

% Please define a domain-name first.

Press RETURN to get started!

*Mar  1 00:00:09.557: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed

*Mar  1 00:00:09.569: *** CRASH_LOG = YES

*Mar  1 00:00:09.569: Port 0 is not present

*Mar  1 00:00:09.569: Port 1 is not presentSecurity Core found.

Base Ethernet MAC address: 70:81:05:EC:45:70

*Mar  1 00:00:10.179: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 41 messages)

*Mar  1 00:00:10.265:  status of voice_diag_test from WLC is false

*Mar  1 00:00:12.375: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up

*Mar  1 00:00:12.405: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1040 Software (C1140-K9W8-M), Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Tue 18-Oct-11 14:52 by prod_rel_team

*Mar  1 00:00:12.405: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start

*Mar  1 00:09:06.060: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Mar  1 00:09:06.060: bsnInitRcbSlot: slot 0 has NO radio

*Mar  1 00:09:06.060: bsnInitRcbSlot: slot 1 has NO radio

*Mar  1 00:09:06.269: %SSH-5-ENABLED: SSH 2.0 has been enabled

*Mar  1 00:09:06.961: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up

*Mar  1 00:09:15.269: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 192.168.37.177, mask 255.255.252.0, hostname AP7081.05ec.4570

*Mar  1 00:09:24.940: %PARSER-4-BADCFG: Unexpected end of configuration file.

*Mar  1 00:09:24.940: %PARSER-4-BADCFG: Unexpected end of configuration file.

*Mar  1 00:09:24.940:  status of voice_diag_test from WLC is false

*Mar  1 00:09:25.008: Logging LWAPP message to 255.255.255.255.

Translating "CISCO-CAPWAP-CONTROLLER.srv.int"...domain server (192.168.38.4)

*Jan 25 12:43:00.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.39.245 peer_port: 5246

*Jan 25 12:43:01.000: %CAPWAP-5-CHANGED: CAPWAP changed state to

*Jan 25 12:43:02.419: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.39.245 peer_port: 5246

*Jan 25 12:43:02.420: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.39.245

*Jan 25 12:43:02.420: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Jan 25 12:43:02.569: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Jan 25 12:43:02.572: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.39.245

*Jan 25 12:43:02.572: %DTLS-5-PEER_DISCONNECT: Peer 192.168.39.245 has closed connection.

*Jan 25 12:43:02.573: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.39.245:5246

*Jan 25 12:43:02.617: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Jan 25 12:43:02.617: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Jan 25 12:43:02.617: bsnInitRcbSlot: slot 0 has NO radio

*Jan 25 12:43:02.617: bsnInitRcbSlot: slot 1 has NO radio

*Jan 25 12:43:02.674:  status of voice_diag_test from WLC is false

*Jan 25 12:43:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.39.245 peer_port: 5246

*Jan 25 12:43:13.001: %CAPWAP-5-CHANGED: CAPWAP changed state to

*Jan 25 12:43:14.419: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.39.245 peer_port: 5246

*Jan 25 12:43:14.420: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.39.245

*Jan 25 12:43:14.420: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Jan 25 12:43:14.560: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Jan 25 12:43:14.563: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.39.245

*Jan 25 12:43:14.563: %DTLS-5-PEER_DISCONNECT: Peer 192.168.39.245 has closed connection.

*Jan 25 12:43:14.563: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.39.245:5246

*Jan 25 12:43:14.609: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Jan 25 12:43:14.610: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Jan 25 12:43:14.610: bsnInitRcbSlot: slot 0 has NO radio

*Jan 25 12:43:14.610: bsnInitRcbSlot: slot 1 has NO radio

*Jan 25 12:43:14.669:  status of voice_diag_test from WLC is false

*Jan 25 12:43:22.844: %CDP_PD-2-POWER_LOW: All radios disabled - NON_CISCO-NO_CDP_RECEIVED  (0000.0000.0000)

*Jan 25 12:43:23.844: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated

*Jan 25 12:43:25.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.39.245 peer_port: 5246

*Jan 25 12:43:25.001: %CAPWAP-5-CHANGED: CAPWAP changed state to

*Jan 25 12:43:26.410: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.39.245 peer_port: 5246

*Jan 25 12:43:26.411: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.39.245

*Jan 25 12:43:26.411: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Jan 25 12:43:26.555: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Jan 25 12:43:26.558: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.39.245

*Jan 25 12:43:26.558: %DTLS-5-PEER_DISCONNECT: Peer 192.168.39.245 has closed connection.

*Jan 25 12:43:26.558: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.39.245:5246

*Jan 25 12:43:26.602: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Jan 25 12:43:26.603: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Jan 25 12:43:26.603: bsnInitRcbSlot: slot 0 has NO radio

*Jan 25 12:43:26.603: bsnInitRcbSlot: slot 1 has NO radio

*Jan 25 12:43:26.660: %PARSER-4-BADCFG: Unexpected end of configuration file.

*Jan 25 12:43:26.660: %PARSER-4-BADCFG: Unexpected end of configuration file.

*Jan 25 12:43:26.661:  status of voice_diag_test from WLC is false

*Jan 25 12:43:37.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.39.245 peer_port: 5246

*Jan 25 12:43:37.001: %CAPWAP-5-CHANGED: CAPWAP changed state to

*Jan 25 12:43:38.418: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.39.245 peer_port: 5246

*Jan 25 12:43:38.419: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.39.245

*Jan 25 12:43:38.419: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Jan 25 12:43:38.559: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Jan 25 12:43:38.561: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.39.245

*Jan 25 12:43:38.562: %DTLS-5-PEER_DISCONNECT: Peer 192.168.39.245 has closed connection.

*Jan 25 12:43:38.562: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.39.245:5246

*Jan 25 12:43:38.608: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Jan 25 12:43:38.608: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Jan 25 12:43:38.609: bsnInitRcbSlot: slot 0 has NO radio

*Jan 25 12:43:38.609: bsnInitRcbSlot: slot 1 has NO radio

*Jan 25 12:43:38.668:  status of voice_diag_test from WLC is false

*Jan 25 12:43:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.39.245 peer_port: 5246

*Jan 25 12:43:49.001: %CAPWAP-5-CHANGED: CAPWAP changed state to

*Jan 25 12:43:50.419: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.39.245 peer_port: 5246

*Jan 25 12:43:50.420: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.39.245

*Jan 25 12:43:50.420: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

*Jan 25 12:43:50.559: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG

*Jan 25 12:43:50.561: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.39.245

*Jan 25 12:43:50.562: %DTLS-5-PEER_DISCONNECT: Peer 192.168.39.245 has closed connection.

*Jan 25 12:43:50.562: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.39.245:5246

*Jan 25 12:43:50.606: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Jan 25 12:43:50.607: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Jan 25 12:43:50.607: bsnInitRcbSlot: slot 0 has NO radio

*Jan 25 12:43:50.607: bsnInitRcbSlot: slot 1 has NO radio

*Jan 25 12:43:50.664:  status of voice_diag_test from WLC is false

What may be the problem ?

Thanks.

2 ACCEPTED SOLUTIONS

Accepted Solutions

Re: AP-1041N LWAPP reboot in a loop

looks like a hardware problem. That BSN 0 not present looks like the AP is not able to detect the 2.4GHz radio. I'd call TAC and get an RMA

Steve

Sent from Cisco Technical Support iPhone App

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
Hall of Fame Super Gold

AP-1041N LWAPP reboot in a loop

*Mar  1 00:00:09.569: Port 0 is not present

*Mar  1 00:00:09.569: Port 1 is not presentSecurity Core found.

Agree with Steve.  You have a hardware issue.  The 2.4 Ghz radio could be faulty.

4 REPLIES

Re: AP-1041N LWAPP reboot in a loop

looks like a hardware problem. That BSN 0 not present looks like the AP is not able to detect the 2.4GHz radio. I'd call TAC and get an RMA

Steve

Sent from Cisco Technical Support iPhone App

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
Hall of Fame Super Gold

AP-1041N LWAPP reboot in a loop

*Mar  1 00:00:09.569: Port 0 is not present

*Mar  1 00:00:09.569: Port 1 is not presentSecurity Core found.

Agree with Steve.  You have a hardware issue.  The 2.4 Ghz radio could be faulty.

New Member

AP-1041N LWAPP reboot in a loop

Many thanks all !
We will request RMA.

Hall of Fame Super Gold

AP-1041N LWAPP reboot in a loop

Thank you for the ratings. 

1717
Views
0
Helpful
4
Replies
CreatePlease to create content