Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

AP 1310 - distance from Power injector

I need to place my 1300 antenna some distance away from the power injector.

Is there a distance limitation on the 2 coax cables connecting the antenna to the power injector?

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

Re: AP 1310 - distance from Power injector

Hi John,

The distance limitation is listed @ 100 meters.

Dual coaxial cable to run from the power injector to the 1300. See attached notes:

Cisco Aironet 1300 Series

Cisco Aironet 1300 Series Access Point/Bridge Power Injector

The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.

From this link:

http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html

Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide

Ethernet Ports

The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.

Power

The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.

From this link:

http://www.cisco.com/en/US/products/ps5861/products_installation_guide_book09186a00804d3095.html

AIR-PWRINJ-BLR2

F-Type Connectors

Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)

From this link:

http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html

Hope this helps!

Rob

1 REPLY
Hall of Fame Super Red

Re: AP 1310 - distance from Power injector

Hi John,

The distance limitation is listed @ 100 meters.

Dual coaxial cable to run from the power injector to the 1300. See attached notes:

Cisco Aironet 1300 Series

Cisco Aironet 1300 Series Access Point/Bridge Power Injector

The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.

From this link:

http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html

Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide

Ethernet Ports

The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.

Power

The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.

From this link:

http://www.cisco.com/en/US/products/ps5861/products_installation_guide_book09186a00804d3095.html

AIR-PWRINJ-BLR2

F-Type Connectors

Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)

From this link:

http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html

Hope this helps!

Rob

674
Views
0
Helpful
1
Replies