Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

AP will not pass DHCP

Hey all,  I'm hoping someone can help with a problem I am having with a AIRONET 1130AG Access point.

I have installed quite a few of these but this one has me baffeled.  Now, I'm not a CCNA or anything like that.

I set up using the GUI;  I use a simple WPA.

My devices connect with "Limited or no Connectivity"    If I hard code an address, devices work fine.  If I attach them to the switch, they obtain an address on the nic AND the Wirless connections.

It seems the AP just wont let DHCP pass

If i check the AP,  it shows my devices, but no IP.  Under the log, the last entry say  "interface Dot11Radio0, Deauthenticating Station (mac address) reason:  Previous authentication no longer valid"

Any advice is greatly appreciated.

Thanks,

John

7 REPLIES
Cisco Employee

Re: AP will not pass DHCP

AP configuration please where is the DHCP configured??

regards

surendra

New Member

Re: AP will not pass DHCP

I have DHCP running on a Domain Controller.  Originally DHCP was running on a router, but I changed it to the DC to see if it made a diference.  it did not.

Here is my #sh config.  Probably more info than you needed.  Thanks for taking a look

ap#sh config
Using 1692 out of 32768 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
enable secret 5 $1$nIl9$Sp2TU/oQNSjgLEhgPoKPj.
!
no aaa new-model
!
!
dot11 syslog
!
dot11 ssid AMHS1
   authentication open
   authentication key-management wpa optional
   guest-mode
   wpa-psk ascii 7 11594955464153543B2B27283B30272B031305
!
!
!
username Cisco password 7 01300F175804
!
!
bridge irb
!
!
interface Dot11Radio0
no ip address
no ip route-cache
!
encryption mode ciphers tkip wep128
!
ssid AMHS1
!
speed  5.5 basic-11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
!
encryption mode ciphers tkip wep128
!
ssid AMHS1
!
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface BVI1
ip address 172.20.1.86 255.255.255.0
no ip route-cache
!
ip default-gateway 172.20.1.30
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
login local
!
end

ap#

Thanks again,

John

Re: AP will not pass DHCP

can you post the switch config that this AP connects too?

Do you have IP helpers set up?

__________________________________________________________________________________________ "Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin ___________________________________________________________
New Member

Re: AP will not pass DHCP

No programming was done on the switch.  It's just out of the box.

Right now I have an old linksys wireless connected to the switch with no security, and clients connect to that just fine.

I set the AP up through the GUI, I didnt see an IP helper option.  Not sure if it set defaulted to on/off.

Not really familiar with IP helper.

Thank you

Re: AP will not pass DHCP

Your linksys ... Is it handing out the IP addresses? Are you using the same subnet ?

__________________________________________________________________________________________ "Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin ___________________________________________________________

Re: AP will not pass DHCP

Is your GW really .30?

nterface BVI1
ip address 172.20.1.86 255.255.255.0
no ip route-cache
!
ip default-gateway 172.20.1.30

__________________________________________________________________________________________ "Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin ___________________________________________________________
New Member

Re: AP will not pass DHCP

No DHCP running on the Linksys.  Yea .30 is my gateway.  Using a SonicWALL firewall

516
Views
0
Helpful
7
Replies