Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

Bronze

Cisco 877 wireless password

Dear All ,

I configure the below on my Cisco877 router , I can connect to wireless but no password authentication .But when i change authentication method it doesn't connect .

The below is my config. with this i can connect, but no password

bridge irb

interface Dot11Radio0

no ip address

broadcast-key vlan 1 change 30

encryption vlan 1 mode ciphers wep40

ssid Shekkeer

    authentication open

    guest-mode

    wpa-psk ascii 0 0125345235

speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0

54.0

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

interface Vlan1

bridge-group 1

bridge 1 protocol ieee

bridge 1 route ip

Regards

Haris P

8 REPLIES

Re: Cisco 877 wireless password

replace

encryption vlan 1 mode ciphers wep40

with

encryption vlan 1 mode ciphers tkip

WPA goes with tkip encryption, not wep.

Regards,

Nicolas

===

Don't forget to rate answers that you find useful

Bronze

Re: Cisco 877 wireless password

Dear Nicholas,

I tried the command you specified ,but it is still connecting without

any password ? Any Clues

The below is my runnning config

interface Dot11Radio0

no ip address

!

broadcast-key vlan 1 change 30

!

!

encryption vlan 1 mode ciphers tkip

!

ssid Shekkeer

authentication open

guest-mode

wpa-psk ascii 0 0102038989

!

ssid Test

authentication open

wpa-psk ascii 0 cisco123

!

speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0

36.0 48.0 54.0

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

Shekkeer(config-if-ssid)#authentication key-management wpa

Error: Encryption mode cipher is not configured

Re: Cisco 877 wireless password

Yes I forgot one command actually :

authentication key-management wpa

To be typed under your SSID configuration.
That should definitely work then.
Nicolas
===
Don't forget to rate answers that you find useful

Bronze

Re: Cisco 877 wireless password

Dear Nicholas ,

I already tried that command

#interface Dot11Radio0

ssid Test

authentication key-management wpa

Error: Encryption mode cipher is not configured

When I added Encription cipher ,it doesn't connect with the ssid

password ..I dont know what's happening

Regards

Re: Cisco 877 wireless password

It's a small "cosmetic" problem I guess.

Because your ssid is in vlan 1 you should replace "encryption vlan 1 mode ciphers tkip" with  "encryption mode ciphers tkip"

Then it should allow you to go for "key-management wpa"

Nicolas

Cisco Employee

Re: Cisco 877 wireless password

if you configure the below command

"encryption vlan 1 mode ciphers tkip" then under the SSID you need to map the VLA Nas well.. that is..

dot11 ssid

vlan 1

auth open

So, my wild guess.. can we reconfigure the same from the scratch? by deleting the SSID and then reconfiguring..

Regards

Surendra

Cisco Employee

Re: Cisco 877 wireless password

and also make sure.. in autonomous.. its as simple as this.. ONE SSID : ONE VLAN mapping

Regards

Surendra

Bronze

Re: Cisco 877 wireless password

It worked with below config...Thanks everyone for your help

Im, posting the config. I hope it will help some one in future

bridge irb

interface Dot11Radio0

no ip address

!

broadcast-key vlan 1 change 30

!

!

!

encryption mode ciphers tkip

!

ssid TEST

    authentication open

    authentication key-management wpa

    guest-mode

    wpa-psk ascii 0 0102058745

!

speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0

54.0

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

interface Vlan1

no ip address

ip nat inside

ip virtual-reassembly

bridge-group 1

ip route 0.0.0.0 0.0.0.0 Dialer1

!

ip nat inside source list 102 interface Dialer1 overload

bridge 1 protocol ieee

bridge 1 route ip

1436
Views
19
Helpful
8
Replies