Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CISCO LAP1142N-A-K9

   I have a question with the CAPWAP command. Typically, when I get 1142N from our provider, they have no configuration on them and all I need to do is enter 4 lines of code all starting with CAPWAP and then I have them join the controller and finish the config. This one I just received looks like it has an IOS image or configuration on it. (You can do a show run). I can: show CAPWAP - but I can not enter any CAPWAP commands. They are invalid input detected at marker.  How to I get to the point where I can enter my CAPWAP commands ??             

Everyone's tags (1)
3 REPLIES

CISCO LAP1142N-A-K9

Can you upload a show version of your AP?

thanks

Stefan

New Member

CISCO LAP1142N-A-K9

APf0f7.5579.3e32#show ver
Cisco IOS Software, C1140 Software (C1140-RCVK9W8-M), Version 12.4(21a)JA, RELEA
SE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 08-Jun-09 16:28 by prod_rel_team

ROM: Bootstrap program is C1140 boot loader
BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA3, RELEASE SOFTWARE
(fc1)

APf0f7.5579.3e32 uptime is 1 hour, 43 minutes
System returned to ROM by reload
System image file is "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"
Last reload reason:

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-LAP1142N-A-K9    (PowerPC405ex) processor (revision B0) with 98294K/32
768K bytes of memory.
Processor board ID FTX1605K16Q
PowerPC405ex CPU at 586Mhz, revision number 0x147E
Last reset from reload
LWAPP image version 3.0.51.0
1 Gigabit Ethernet interface

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F0:F7:55:79:3E:32
Part Number                          : 73-12836-04
PCA Assembly Number                  : 800-33767-04
PCA Revision Number                  : A0
PCB Serial Number                    : FOC1602604U
Top Assembly Part Number             : 800-33775-03
Top Assembly Serial Number           : FTX1605K16Q
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1142N-A-K9

Configuration register is 0xF

APf0f7.5579.3e32#

Cisco Employee

CISCO LAP1142N-A-K9

#k9w8 is capwap image.

#execute the below command and try capwap commands.

WLC>debug capwap console client

AP#show ip int bri. You shouldn't see BVI interface, and show run config shouldn't show ios stuff. If you're seeing these then reimage the AP with recovery image.

726
Views
0
Helpful
3
Replies