Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

data rate configurations

Dear All,

in cisco WLC,

can we disable certain data rate for specific WLAN/SSID  instead of using global paramaters ???

(Wireless > 802.11a/n or 802.11b/g/n Network to open the 802.11a (or 802.11b/g) Global Parameters page)


12 REPLIES

Re: data rate configurations

No sorry .. Global only ..

Sent from Cisco Technical Support iPad App

__________________________________________________________________________________________ "Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin ___________________________________________________________
Hall of Fame Super Gold

Re: data rate configurations

can we disable certain data rate for specific WLAN/SSID  instead of using global paramaters ???

Yes you can.  If you enable RF Profile.  Wireless > RF Profile

NOTE:  Not available in all codes.  I believe it's supported in 7.3.X and up.

New Member

Re: data rate configurations

When we apply rf profile , does it means we associate the rf profile to AP groups ?

Therefore I think, it is per AP level (affecting all WLAN inside)  not per WLAN/SSID.

Hall of Fame Super Gold

data rate configurations

When we apply rf profile , does it means we associate the rf profile to AP groups ?

Yes.

Therefore I think, it is per AP level (affecting all WLAN inside)  not per WLAN/SSID.

No.  It's SSID-level too.  You put your APs in an AP Group, attach the RF Profile in.

Re: data rate configurations

I just got schooled !

+5 Leo

Sent from Cisco Technical Support iPad App

__________________________________________________________________________________________ "Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin ___________________________________________________________
Hall of Fame Super Silver

Re: data rate configurations

Haha

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***
Hall of Fame Super Gold

data rate configurations

Thanks for the ratings, George. 

Cisco Employee

Re: data rate configurations

Rf profiles made their debut in 7.2

Sent from Cisco Technical Support iPhone App

Re: data rate configurations

To define the data rates on a per-SSID basis, do the following:

  1. Define  the average data rate TCP traffic per SSID by entering the rate in Kbps  in the Average Data Rate text boxes. A value of 0 indicates that the  value specified in the selected QoS profile will take effect.
  2. Define the  peak data rate for TCP traffic per SSID by entering the rate in Kbps in  the Burst Data Rate text boxes. A value of 0 indicates that the value  specified in the selected QoS profile will take effect. 
    Note   

    The burst data rate should  be greater than or equal to the average data rate. Otherwise, the QoS  policy may block traffic in the WLANs.

  3. Define the  average real-time rate for UDP traffic per SSID by entering the rate in  Kbps in the Average Real-Time Rate text boxes. A value of 0 indicates  that the value specified in the selected QoS profile will take effect.
  4. Define  the peak real-time rate for UDP traffic per SSID by entering the rate in  Kbps in the Burst Real-Time Rate text boxes. A value of 0 indicates  that the value specified in the selected QoS profile will take effect. 
    Note   

    The burst real-time rate  should be greater than or equal to the average real-time rate.  Otherwise, the QoS policy may block traffic in the WLANs.

Please refer the below link  ( Qos )

http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/consolidated/b_cg74_CONSOLIDATED_chapter_01010111.html

Re: data rate configurations

I think he was asking for PHY rates not thoughtput .. And btw RF profile is based around AP not SSID.

__________________________________________________________________________________________
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
__________________________________________________________________________________________
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

__________________________________________________________________________________________ "Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin ___________________________________________________________
New Member

Re: data rate configurations

george is right

I am asking for PHY rate

And also I agree with george, RF profile is around AP not SSID.

Well, FYI, I experienced with Aruba in the past, and Aruba Mobility Controller can do rate configurations around

virtual AP/SSID (not per AP level).

thanks all !.

regards

Saleh Iskandar

Re: data rate configurations

Which leads me back to my original comment , it's not supported .. Lol

Sent from Cisco Technical Support iPhone App

__________________________________________________________________________________________ "Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin ___________________________________________________________
258
Views
10
Helpful
12
Replies
CreatePlease to create content