Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Ip secondary

When i add ip address 10.100.100.1 255.255.255.0 secondary to interface Bv1 and i type show running-config i can't see secondary ip address.Why?

Many Thanks

ap# sh ver

Cisco Internetwork Operating System Software

IOS (tm) C1200 Software (C1200-K9W7-M), Version 12.2(11)JA1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Mon 07-Jul-03 13:48 by ccai

Image text-base: 0x00003000, data-base: 0x004D46F4

ROM: Bootstrap program is C1200 boot loader

BOOTLDR: C1200 Boot Loader (C1200-BOOT-M) Version 12.2(8)JA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

ap uptime is 14 minutes

System returned to ROM by power-on

System image file is "flash:/c1200-k9w7-mx.122-11.JA1/c1200-k9w7-mx.122-11.JA1"

Using 2325 out of 32768 bytes

!

version 12.2

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname CISCO-AP50

!

ip subnet-zero

!

dot11 network-map

!

bridge irb

!

!

interface Dot11Radio0

no ip address

no ip route-cache

!

ssid xxxxxxx

vlan 50

authentication open

authentication shared

!

ssid xxxxxxx

vlan 51

authentication open

!

ssid tsunami

authentication open

guest-mode

!

speed basic-1.0 basic-2.0 basic-5.5 basic-11.0

rts threshold 2312

station-role root

!

interface Dot11Radio0.1

encapsulation dot1Q 1

no ip route-cache

!

interface Dot11Radio0.50

encapsulation dot1Q 50 native

no ip route-cache

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

!

interface Dot11Radio0.51

encapsulation dot1Q 51

no ip route-cache

bridge-group 51

bridge-group 51 subscriber-loop-control

bridge-group 51 block-unknown-source

no bridge-group 51 source-learning

no bridge-group 51 unicast-flooding

bridge-group 51 spanning-disabled

!

interface FastEthernet0

no ip address

no ip route-cache

duplex auto

speed auto

!

interface FastEthernet0.1

encapsulation dot1Q 1 native

no ip route-cache

bridge-group 1

no bridge-group 1 source-learning

bridge-group 1 spanning-disabled

!

interface FastEthernet0.50

encapsulation dot1Q 50

no ip route-cache

!

interface FastEthernet0.51

encapsulation dot1Q 51

no ip route-cache

bridge-group 51

no bridge-group 51 source-learning

bridge-group 51 spanning-disabled

!

interface BVI1

ip address 192.168.0.2 255.255.255.0

!

ip http server

ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag/ivory/1100

bridge 1 route ip

!

!

line con 0

line vty 0 4

login local

line vty 5 15

login

!

end

6 REPLIES
New Member

Re: Ip secondary

Hi,

Try using show interface to see secondary IP addresses.

On a security note you may want to read this if you haven't done so already.

http://www.cisco.com/warp/public/707/cisco-sn-20030730-ios-2gb-get.shtml

R/S

Dave

New Member

Re: Ip secondary

Hi,

i tried to show interface but i didn't see the new ip secondary address.

Why?

Thanks

Marco

Anonymous
N/A

Re: Ip secondary

Hi Marco,

Have you found why you can't see the new ip secondary address ? I have the same proble on a 1200.

Thanks,

Eric

New Member

Re: Ip secondary

Sorry,i can't find solution.

Marco

New Member

Re: Ip secondary

Try this - it seems to create a second instance of the BVI 1 interface.

ap#conf t

Enter configuration commands, one per line. End with CNTL/Z.

ap(config)#int bvI 1:0

ap(config-if)#

ap(config-if)#ip address 10.2.2.2 255.255.255.0

ap(config-if)#end

ap#sh ip int brief

Interface IP-Address OK? Method Status Protocol

BVI1 192.168.54.1 YES NVRAM up up

BVI1 10.2.2.2 YES manual up up

both addresses can be pinged

Green

Re: Ip secondary

Just curious: Why are you putting a second IP address on the AP, when it does no routing (the address is just there for management)?

Thanks

Scott

231
Views
0
Helpful
6
Replies