Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

Power Injector

 

Hello,

Please, we need the right specification to the power injector model for Cisco 1532 series access point. I will appreciate if the part number and picture is sent to me

 

Regards,

Ethelbert

8 REPLIES
VIP Purple

HiHere is the part number

Hi

Here is the part number detail

AIR-PWRADPT-1530=

http://www.cisco.com/c/en/us/td/docs/wireless/access_point/1530/power/guide/1530pwradpt.html

Here is the 1530 AP deployment guide for your reference

http://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/7-6/b_1532_dg.pdf

HTH

Rasika

**** Pls rate all useful responses ****

Community Member

 Hello Rasika, Thanks for

 

Hello Rasika,

 

Thanks for your email,

The part number and documentation you sent earlier is for power adapter. Am requesting for Cisco 1532 access point  power injector part number.

Please, help.

Thanks.

 

Regards,

Ethelbert

VIP Purple

Sorry, I may misread your

Sorry, I may misread your requirement. If you require power injector this should be the part number. Given deployment guide should listed this

AIR-PWRINJ1500-2=

Here is the different power option in a summarized view

 

Please mark thread answered if you get what you require.

HTH

Rasika 

 

Cisco Employee

Power injectorsThe 1530

Power injectors

The 1530 series access points support the following power injectors:

  • AIR-PWRINJ1500-2= – 100-240 VAC input, indoor use only
  • AIR-PWRINJ-30= – 100-240 VAC input, indoor use only
 
 

 Caution The power injector (AIR-PWRINJR4- and AIR-PWRINJ1500-2=) must be used in an indoor environment only.

Bronze

The 1532 access point

The 1532 access point supports these power sources:

  • DC power – 24- 57 VDC
  • Power-over-Ethernet (PoE)

The 1532 access point can be powered via the PoE input from an in-line power injector or a suitably powered switch port. Depending on the configuration and regulatory domain, the required power for full operation is UPoE. For the 1532E, 802.3at power is sufficient for all regulatory domains and full 2x2 MIMO operation on both 2.4 and 5 GHz radios. Either the AIR-PWRINJ-30= or the AIR-PWRINJ1500-2= power injector can be used.

For the 1532I, UPoE powered switch port or the AIR-PWRINJ1500-2= power injector is required for full operation of the 3x3 MIMO on the 2.4 GHz radio in the regulatory domains that allow for high 2.4 GHz transmit power (Regulatory domains -A, -D, -F, -K, -N, -Q, -T, -Z). If the 1532I is powered by a PoE+ (802.3at power) switch port or the AIR-PWRINJ-30= power injector, then the access point will automatically disable one of the 2.4 GHz transmitters and the radio will operate in 2x3 MIMO mode.

Please refer: http://www.cisco.com/c/en/us/td/docs/wireless/access_point/1530/installation/guide/1530hig/1530_ch2.html#24750

Power injectorsThe 1530

Power injectors

The 1530 series access points support the following power injectors:

  • AIR-PWRINJ1500-2= – 100-240 VAC input, indoor use only
  • AIR-PWRINJ-30= – 100-240 VAC input, indoor use only
Community Member

Hi Ethelbert,Could you be

Hi Ethelbert,

Could you be able to get a picture of AIR-PWRINJ-30= ? I´m looking for it

thanks

Community Member

Just use the AIR-PWRINJ-30=

Just use the AIR-PWRINJ-30= power injector for the 1532e model. Make sure you use the "poe-in" port on the 1532 AP to connect to the power injector.

916
Views
10
Helpful
8
Replies
CreatePlease to create content