Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

wireless mobility agent question

Hello,

 

I have created a switch peer group between two 3850's. Should I have to create all the WLAN's and ap-groups on the agent as well as the controller. This seems wrong. I would assume all setup would be done on the mobility controller and pushed to the agent but maybe I'm wrong.

 

Mobility Controller Summary:

Mobility Role                                   : Mobility Controller
Mobility Protocol Port                          : 16666
Mobility Group Name                             : wireless
Mobility Oracle IP Address                      : 0.0.0.0
DTLS Mode                                       : Enabled
Mobility Domain ID for 802.11r                  : 0x89f
Mobility Keepalive Interval                     : 10
Mobility Keepalive Count                        : 3
Mobility Control Message DSCP Value             : 48
Mobility Domain Member Count                    : 1

Link Status is Control Link Status : Data Link Status

Controllers configured in the Mobility Domain:

IP               Public IP        Group Name       Multicast IP     Link Status
-------------------------------------------------------------------------------
10.120.136.5     -                coop-refinery-wireless 0.0.0.0          UP   : UP

Switch Peer Group Name            : tester
Switch Peer Group Member Count    : 1
Bridge Domain ID                  : 0
Multicast IP Address              : 0.0.0.0

IP               Public IP             Link Status
--------------------------------------------------
10.120.140.5     10.120.140.5         UP : UP

 

 

 

 


Mobility Agent Summary:

Mobility Role                                   : Mobility Agent
Mobility Protocol Port                          : 16666
Mobility Switch Peer Group Name                 : tester
Multicast IP Address                            : 0.0.0.0
DTLS Mode                                       : Enabled
Mobility Domain ID for 802.11r                  : 0x89f
Mobility Keepalive Interval                     : 10
Mobility Keepalive Count                        : 3
Mobility Control Message DSCP Value             : 48
Switch Peer Group Members Configured            : 1

Link Status is Control Link Status : Data Link Status

The status of Mobility Controller:

IP              Public IP            Link Status
------------------------------------------------
10.120.136.5    10.120.136.5         UP : UP

Switch Peer Group members:

IP              Public IP            Data Link Status
-----------------------------------------------------
10.120.140.5    10.120.140.5         UP

 

 

 

Thanks

Dallas

2 ACCEPTED SOLUTIONS

Accepted Solutions
VIP Purple

Hi Dallas,As of today you do

Hi Dallas,

As of today you do not have the luxury of creating all WLAN/AP group config on your MC & then it will push it for MA.

So you have to configure all your MA identically for WLAN/AP group etc.

 

HTH

Rasika

**** Pls rate all useful responses ****

Hi, Mobility Agent is a

Hi,

 

Mobility Agent is a dedicated controller at the end of the day. It just depends on the Mobility controller for few of its requirements like Mobility. For everything else , you should consider it as a normal controller and configure individually as you do on CUWN WLCs.

 

Regards

Dhiresh

3 REPLIES
VIP Purple

Hi Dallas,As of today you do

Hi Dallas,

As of today you do not have the luxury of creating all WLAN/AP group config on your MC & then it will push it for MA.

So you have to configure all your MA identically for WLAN/AP group etc.

 

HTH

Rasika

**** Pls rate all useful responses ****

New Member

Thank you both for the

Thank you both for the replies.

Hi, Mobility Agent is a

Hi,

 

Mobility Agent is a dedicated controller at the end of the day. It just depends on the Mobility controller for few of its requirements like Mobility. For everything else , you should consider it as a normal controller and configure individually as you do on CUWN WLCs.

 

Regards

Dhiresh

64
Views
0
Helpful
3
Replies