Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

WiSM in a Cat6500

we have two wisms in a cat6500, I wonder how can you log into the wism from the switch. to be more specifically, how can I know the processor number?

thanks,

han

4 REPLIES

WiSM in a Cat6500

This only will work if you have the Service Port configured porperly.

from the Sup

session slot x proc y.  so if you had a WiSM in slot 4 and wanted to get into the first WLC

session slot 4 proc 1

Steve

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
New Member

WiSM in a Cat6500

Steve,

I tried,

session slot 7 proc 0--9, none of them works. and i pretty sure, it was configured right.

here is show module command, any idea

=====

c6509-w1#sho module

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE      SAD10470C9L

  5    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAD103701FT

  7   10  WiSM WLAN Service Module               WS-SVC-WISM-1-K9   SAD18450A28

  8    6  Firewall Module                        WS-SVC-FWM-1       SAD104702X1

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  1  0019.aacc.a772 to 0019.aacc.a875   2.4   12.2(14r)S5  12.2(33)SXI5 Ok

  5  0011.9202.7ac0 to 0011.9202.78c3   5.2   8.4(2)       12.2(33)SXI5 Ok

  7  0019.aacc.8254 to 0019.aacc.8863   1.4   12.2(14r)S5  12.2(33)SXI5 Ok

  8  0019.aaf4.ad36 to 0019.aaf4.ad8d   4.1   7.2(1)       4.0(16)      Ok

Mod  Sub-Module                  Model              Serial       Hw     Status

---- --------------------------- ------------------ ----------- ------- -------

  1  Centralized Forwarding Card WS-F6700-CFC       SAD10450BK4  3.0    Ok

  5  Policy Feature Card 3       WS-F6K-PFC3B       SAD102900WV  2.3    Ok

  5  MSFC3 Daughterboard         WS-SUP720          SAD103106H0  2.5    Ok

  7  Centralized Forwarding Card WS-SVC-WISM-1-K9-D SAD10450AED  1.4    Ok

Mod  Online Diag Status

---- -------------------

  1  Pass

  5  Pass

  7  Pass

  8  Pass

WiSM in a Cat6500

it would have been session slot 7 proc 1 | 2

can you post the output of show wism status

Steve

HTH, Steve ------------------------------------------------------------------------------------------------ Please remember to rate useful posts, and mark questions as answered
Silver

Re: WiSM in a Cat6500

Perhaps a show wism summary    (or is it status?)               to confirm that the service port and everything up and running fine?

Either way, as Stephen said, basic syntax is: session slot [X] proc [1 or 2]

EDIT: (and now I just read that Stephen also mentioned the making sure the service port is configured correctly)

358
Views
0
Helpful
4
Replies