cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
279
Views
0
Helpful
1
Replies

WLC4402 change AP IOS

a.crippa
Level 1
Level 1

Hi to all,

I have a WLC4402 and ten LAP1242, works fine, but I need to use two of this AP as bridge (only for few weeks), so I want to change the IOS from LWAPP to autonomus AP IOS.

Can anybody suggest any document to perform this IOS change (from LWAPP to AP and the opposite), and there are any problem or issue to do when I back this AP to WLC infrastructure?

Thank you much.

Augusto.

1 Accepted Solution

Accepted Solutions

Rob Huffman
Hall of Fame
Hall of Fame

Hi Augusto,

Here is the method to revert the AP's to IOS Versions. You can then upgrade them to LWAPP later using the method in the doc below :)

Using a TFTP Server to Return to a Previous Release

--------------------------------------------------------------------------------

Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.

--------------------------------------------------------------------------------

Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:

--------------------------------------------------------------------------------

Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.

Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.

Step 3 On the PC where the TFTP server is located, perform these steps:

a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.

b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.

Step 4 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.

Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.

Step 6 Disconnect power from the access point.

Step 7 Press and hold MODE while you reconnect power to the access point.

Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.

Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.

Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.

http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918

Hope this helps!

Rob

View solution in original post

1 Reply 1

Rob Huffman
Hall of Fame
Hall of Fame

Hi Augusto,

Here is the method to revert the AP's to IOS Versions. You can then upgrade them to LWAPP later using the method in the doc below :)

Using a TFTP Server to Return to a Previous Release

--------------------------------------------------------------------------------

Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.

--------------------------------------------------------------------------------

Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:

--------------------------------------------------------------------------------

Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.

Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.

Step 3 On the PC where the TFTP server is located, perform these steps:

a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.

b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.

Step 4 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.

Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.

Step 6 Disconnect power from the access point.

Step 7 Press and hold MODE while you reconnect power to the access point.

Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.

Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.

Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.

http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918

Hope this helps!

Rob

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: