Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

VSOM 6.3.3 Drive Rebuild

Hello all!

I was wondering if someone can post the commands to check a drive rebuild status for VSOM 6.3.3. I can see it via the WebIOS but need to check remotely. This is on an MSP series server running Linux.

Thanks

Everyone's tags (3)
1 ACCEPTED SOLUTION

Accepted Solutions
Silver

VSOM 6.3.3 Drive Rebuild

/opt/MegaRAID/MegaCli/MegaCli -pdrbld -showprog -physdrv "[:]" -a0

... likely.

Others are:

Info on the raid (assuming the raid is a0)

/opt/MegaRAID/MegaCli/MegaCli -ldinfo -lall -a0

/opt/MegaRAID/MegaCli/MegaCli -pdlist -a0

The file MegaSAS.log from the current directory will also contain the output of the commands,

To start the rebuild of drive 0, run the command (only if it didn't start on its own), this makes the drive a hot spare:

/opt/MegaRAID/MegaCli/MegaCli -pdrbld -start -physdrv "[:]" -a0

If a drive gets marked as "foreign", clear the foreign configuration:

/opt/MegaRAID/MegaCli/MegaCli -CfgForeign -Clear -a0

And, to silence the beeping:

/opt/MegaRAID/MegaCli/MegaCli -adpsetprop AlarmSilence -aALL

Flash start / stop

/opt/MegaRAID/MegaCli/MegaCli -pdlocate start physdrv [8:1] -a0 -nolog

/opt/MegaRAID/MegaCli/MegaCli -pdlocate stop physdrv [8:1] -a0 -nolog

Hope this helps!!

Scott Olsen
Solutions Specialist
Bulletproof Solutions Inc.
Web: www.bulletproofsi.com


Scott Olsen Solutions Specialist Bulletproof Solutions Inc. Web: www.bulletproofsi.com
2 REPLIES
Silver

VSOM 6.3.3 Drive Rebuild

/opt/MegaRAID/MegaCli/MegaCli -pdrbld -showprog -physdrv "[:]" -a0

... likely.

Others are:

Info on the raid (assuming the raid is a0)

/opt/MegaRAID/MegaCli/MegaCli -ldinfo -lall -a0

/opt/MegaRAID/MegaCli/MegaCli -pdlist -a0

The file MegaSAS.log from the current directory will also contain the output of the commands,

To start the rebuild of drive 0, run the command (only if it didn't start on its own), this makes the drive a hot spare:

/opt/MegaRAID/MegaCli/MegaCli -pdrbld -start -physdrv "[:]" -a0

If a drive gets marked as "foreign", clear the foreign configuration:

/opt/MegaRAID/MegaCli/MegaCli -CfgForeign -Clear -a0

And, to silence the beeping:

/opt/MegaRAID/MegaCli/MegaCli -adpsetprop AlarmSilence -aALL

Flash start / stop

/opt/MegaRAID/MegaCli/MegaCli -pdlocate start physdrv [8:1] -a0 -nolog

/opt/MegaRAID/MegaCli/MegaCli -pdlocate stop physdrv [8:1] -a0 -nolog

Hope this helps!!

Scott Olsen
Solutions Specialist
Bulletproof Solutions Inc.
Web: www.bulletproofsi.com


Scott Olsen Solutions Specialist Bulletproof Solutions Inc. Web: www.bulletproofsi.com
Community Member

VSOM 6.3.3 Drive Rebuild

Thats what I needed. Thank you!

654
Views
0
Helpful
2
Replies
CreatePlease to create content