07-01-2013 07:34 AM - edited 03-18-2019 01:23 AM
We see a strange issue in Cisco C20, where in the Video input from Camera is not detected in the Codec - But the far end is able to see the Camera video if we are in a call.
Xstatus Video Input says - Not connected.
We see the same with TC5.1.6 and TC 6.1. The camera works fine with other Codec.
When connected to the vpe1 of the Codec - it shows the HDMI 1 has no signal and is disabled.
ad9388a: no HDMI signal, no DVI-D signal, unknown analog signal
videorx: source HDMI-1 (128) on primary input, disabled, not encrypted
Is this a Hardware issue with Video Processor of the Codec.?
vpe-info all
FPGA 1, max 6/2 loc/dsp0 windows
32 phases, selected phase/quality 0/352
phases 0- 7: 352 352 0 352 124 0 0 0
phases 8-15: 0 0 0 0 0 0 0 0
phases 16-23: 0 0 0 0 0 0 0 0
phases 24-31: 0 0 0 0 4 351 352 352
valid local inputs for FPGA 1:
17 (Multiplexed video link)
33 (Internal Video Path) (1280x720@60)
66 (Decoded video stream) (1920x1080)
128 (HDMI) (0x0)
valid remote inputs for FPGA 1:
16 (Multiplexed video link)
64 (Decoded video stream)
81 (Menu stream) (1280x720)
valid outputs for FPGA 1:
1 (HDMI) (1280x720@60)
33 (Internal Video Path) (1280x720@60)
66 (DSP0) (0x0)
80 (DSP2) (0x0)
inactive window configuration for HDMI output on FPGA 1:
0: 10000x10000@0x0 source 81 fitmode 1 border 0 active 1
1: 10000x10000@0x0 source 33 fitmode 0 border 0 active 1
inactive window configuration for Internal Video Path output on FPGA 1:
1: 10000x10000@0x0 source 66 fitmode 2 border 0 active 1
4: 2150x2150@7800x4770 source 17 fitmode 1 border 1 active 1
inactive window configuration for DSP0 output on FPGA 1:
inactive window configuration for DSP2 output on FPGA 1:
active window configuration for HDMI output on FPGA 1:
0: 10000x10000@0x0 source 81 fitmode 1 border 0 active 1
1: 10000x10000@0x0 source 33 fitmode 0 border 0 active 1
active window configuration for Internal Video Path output on FPGA 1:
1: 10000x10000@0x0 source 66 fitmode 2 border 0 active 1
4: 2150x2150@7800x4770 source 17 fitmode 1 border 1 active 1
active window configuration for DSP0 output on FPGA 1:
active window configuration for DSP2 output on FPGA 1:
mux 0: vp3=link 4, source 1
mux 1: vp3=link 0, source 1
mux 2: vp3=link 15, source 0
driver: vpe1 (Orion rev E/ ), uptime: 0d 1h 19m 0s, no GHz ARM
videorx: source HDMI-1 (128) on primary input, disabled, not encrypted
videorx: local input detection: 0x0@0.0
videotx: display on HDMI-1: 1280x720@60 (powersaving off)
frame 1650x750, front porch 110/5, sync width 40/5, polarity +/+, dvi, digital
pix_freq 74.250000 Mhz
videotx: dsp0: 0x0@0
videotx: dsp2: 0x0@0
videotx: internal: 1280x720
videodetector: lvds 4, source 81: 1280x720p
ad9388a: input HDMI, drive strength 3
ad9388a: no HDMI signal, no DVI-D signal, unknown analog signal
ad9388a: digital has no lock, TMDS pll has lock, deglitch filter is on
ad9388a: CSC mode: auto. Detected color space: auto. Coefficient preset selected: 0
ad9389b: detected hotplug, no Rx Sense, no EDID, DVI-D output enabled
ad9389b: no encryption
ad9389b: state: reading EDID, error: i2c error, detect count: 0, msk/irq: c4/20
ad9389b: RGB quantization: full range
ad9389b: manual gear 1
idt5v9885b: 74250 kHz M=16 P=16 D=1 IpRz=0x33 CpCz=0x74
IRQ Total
vpe_timer : 4740
api_req : 28
system_status : 24
core_status : 11419
hdmi_in : 0
hdmi_out : 24
detect_input : 0
pll_lock_lost : 0
ddrcache0 : 0
ddrcache1 : 0
detect_output : 9490
local_scaler : 0
dsp0_scaler : 0
dsp1_scaler : 0
vsink_local : 12
vsink_dsp0 : 0
vsink_dsp1 : 0
vsource_local : 1
vsource_dsp0 : 1913
vsource_dsp1 : 0
local_composer : missing: 5 framereq: 0
dsp0_composer : missing: 0 framereq: 0
dsp1_composer : missing: 0 framereq: 0
local_crop : 0
dsp0_crop : 0
dsp1_crop : 0
dsp0_oversampler : 0
dsp1_oversampler : 0
cec_hdmi_tx : 0
cec_hdmi_rx : 0
OK