Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

1811 Default Chat Script Aborts Dial out

I am configuring an 1811 with built in V.92 modem and I have matched the same settings I am using with a 1711 with a built in WIC modem, and the 1811 built in default chat script is aborting the dial out. How can I rectify this?

DEBUG DIALER

============

Oct 8 08:49:19 PDT: As1 DDR: rotor dialout [best] least recent failure is also most recent failure

*Oct 8 08:49:19 PDT: As1 DDR: rotor dialout [best] also has most recent failure

*Oct 8 08:49:19 PDT: As1 DDR: rotor dialout [best]

*Oct 8 08:49:19 PDT: As1 DDR: Dialing cause ip (s=10.137.1.2, d=10.41.1.4)

*Oct 8 08:49:19 PDT: As1 DDR: Attempting to dial 19057128464

*Oct 8 08:49:19 PDT: CHAT1: Attempting async line dialer script

*Oct 8 08:49:19 PDT: CHAT1: no matching chat script found for 19057128464

*Oct 8 08:49:19 PDT: CHAT1: Dialing using Modem script: d0efault-d0ials0cript & System script: none

*Oct 8 08:49:19 PDT: CHAT1: process started

*Oct 8 08:49:19 PDT: CHAT1: Asserting DTR

*Oct 8 08:49:19 PDT: CHAT1: Chat script d0efault-d0ials0cript started

*Oct 8 08:49:46 PDT: CHAT1: Found abort string BUSY expecting CONNECT

*Oct 8 08:49:46 PDT: CHAT1: Chat script d0efault-d0ials0cript finished, status = Connection aborted

*Oct 8 08:49:46 PDT: As1 DDR: disconnecting call

*Oct 8 08:50:01 PDT: As1 DDR: re-enable timeout

CONFIGURATION

===============

interface Async1

bandwidth 38

ip unnumbered Loopback0

ip virtual-reassembly

encapsulation ppp

ip tcp header-compression

no ip mroute-cache

dialer in-band

dialer pool-member 10

async mode interactive

compress stac

ppp authentication chap

!

interface Dialer10

bandwidth 38

ip unnumbered Loopback0

ip nat outside

ip virtual-reassembly

encapsulation ppp

ip tcp header-compression

no ip mroute-cache

dialer pool 10

dialer remote-name lclas5400a-on.ca

dialer string 19057128464

dialer-group 10

compress stac

ppp authentication chap

!

line con 0

password 7 141B1107

login authentication MIS-Access

line 1

exec-timeout 0 0

login authentication MIS-Access

modem InOut

transport preferred none

transport input all

transport output none

autoselect ppp

stopbits 1

speed 115200

flowcontrol hardware

line aux 0

transport input all

autoselect during-login

autoselect ppp

flowcontrol hardware

line vty 0 4

password 7 020A0757

login authentication MIS-Access

1 REPLY
Silver

Re: 1811 Default Chat Script Aborts Dial out

No, This configuration will works fine.

Please verify you can able to dial the ISP and connect without using a external modem chat script.

If you want to see if the behavior changes, enable the following debugs:

Debug confmodem

Debug chat line 1

Debug ppp ne

Debug ppp authe

Debug dialer

Debug modem

And also recheck the configuration. It may help you.

For the configuration following guide may help you

http://www.cisco.com/en/US/docs/routers/access/1800/1801/software/configuration/guide/dialbkup.html#wp1029902

654
Views
0
Helpful
1
Replies
CreatePlease login to create content