Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

3845 as a Dialup Router?

Hi,

I am using Cisco 3845 as a dialup router. All config is fine but i stuck at aaa configuration. Even the Local dataabse on Router is not auth. output of debug command is:

*May 9 05:48:59.819: AAA/ACCT/EVENT/(0000004B): EXEC DOWN

*May 9 05:49:01.819: AAA/ACCT/HC(0000004B): Update As2/20

*May 9 05:49:01.819: AAA/ACCT/HC(0000004B): As2/20 [pre-sess] (rx/tx) base 0/0 pre 0/0 call 0/0

*May 9 05:49:01.819: AAA/ACCT/HC(0000004B): As2/20 [pre-sess] (rx/tx) adjusted, pre 0/0 call 0/0

*May 9 05:49:01.819: AAA/ACCT/HC(0000004B): Update As2/20

*May 9 05:49:01.819: AAA/ACCT/HC(0000004B): As2/20 [sess] (rx/tx) base 0/0 pre 0/0 call 0/0

*May 9 05:49:01.819: AAA/ACCT/HC(0000004B): As2/20 [sess] (rx/tx) adjusted, pre 0/0 call 0/0

*May 9 05:49:01.819: AAA/ACCT/HC(0000004B): Deregister As2/20

*May 9 05:49:01.819: AAA/ACCT/EVENT/(0000004B): CALL STOP

*May 9 05:49:01.819: AAA/ACCT/CALL STOP(0000004B): Sending stop requests

*May 9 05:49:01.819: AAA/ACCT(0000004B): Send all stops

*May 9 05:49:01.819: AAA/ACCT/NET(0000004B): STOP

*May 9 05:49:01.819: AAA/ACCT/NET(0000004B): Method list not found

*May 9 05:49:01.819: AAA/ACCT(0000004B): del node, session 70

*May 9 05:49:01.819: AAA/ACCT/NET(0000004B): free_rec, count 0

*May 9 05:49:01.819: AAA/ACCT/NET(0000004B) reccnt 0, csr TRUE, osr 0

*May 9 05:49:01.819: AAA/ACCT/NET(0000004B): Last rec in db, intf not enqueued

*May 9 05:49:02.887: %ISDN-6-DISCONNECT: Interface Serial4/0:2 disconnected from 0219215320 , call lasted 45 seconds

Can anyone explain or pointing to any relevant site for basic configuration?

Thanks in advance.

4 REPLIES

Re: 3845 as a Dialup Router?

Can you post your AAA and 'line' configuration?

New Member

Re: 3845 as a Dialup Router?

It's very basic currently,

aaa new-model

aaa authentication login default local

aaa authentication ppp default local

aaa authorization network default local

aaa session-id common

username new password new

controller E1 3/0

pri-group timeslots 1-31

interface Serial3/0:15

ip unnumbered GigabitEthernet0/1

encapsulation ppp

dialer wait-for-line-protocol 20

dialer-group 1

isdn switch-type primary-net5

isdn incoming-voice modem

peer default ip address pool old

fair-queue 64 256 0

no cdp enable

ppp authentication pap

ppp multilink

interface Group-Async1

no ip address

encapsulation ppp

no ip mroute-cache

dialer in-band

dialer idle-timeout 5000

dialer wait-for-line-protocol 20

async mode interactive

peer default ip address pool old

no fair-queue

ppp max-bad-auth 3

ppp multilink

group-range 1 1/29

line 1/1 1/29

session-timeout 35791

exec-timeout 596 31

no flush-at-activation

absolute-timeout 1000

modem InOut

modem autoconfigure discovery

transport input all

autoselect during-login

autoselect ppp

all the relevant config is also there.

Hope u can help. User stuck on 'Verifying username password'

Re: 3845 as a Dialup Router?

I believe that "no login" will prevent the line from trying to auth.

Cisco Employee

Re: 3845 as a Dialup Router?

Is the incoming call an exec call or a ppp call? Exec typically is when you want to dial into a router for OOB management.

I am assuming it's ppp, in that case please add "ppp authentication pap" under "interface Group-Async1"

A couple of good docs on basic configuration:

http://www.cisco.com/en/US/tech/tk59/technologies_tech_note09186a0080093c81.shtml

http://www.cisco.com/en/US/tech/tk59/technologies_configuration_example09186a00800fa54a.shtml

If it does not work then will suggest some debugs to capture.

Thanks, Mak

234
Views
0
Helpful
4
Replies
CreatePlease login to create content