Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Analog Call through BRI

Hi,

I am setting up an old router 3640 with mica modem and a BRI interface. I am trying to call from my PC through an analog line and connect to BRI, but I take the folllowing debug message:

--------------------------------------------------

Jun 1 10:44:35.329: ISDN BR0/0: Incoming call id = 0x0006, dsl 0

Jun 1 10:44:35.333: ISDN BR0/0: LIF_EVENT: ces/callid 1/0x6 HOST_INCOMING_CALL

Jun 1 10:44:35.333: ISDN BR0/0: HOST_INCOMING_CALL: (non-POTS) VOICE

Jun 1 10:44:35.333: ISDN BR0/0: HOST_INCOMING_CALL: (1) call_type = VOICE

Jun 1 10:44:35.333: ISDN BR0/0: HOST_INCOMING_CALL: voice_answer_data = FALSE call type is VOICE ALAW

Jun 1 10:44:35.333: %CSM-1-HWREV: The T1 or E1 network module is incompatible with the digital modems: MODEM_REPORT

Jun 1 10:44:35.333: ISDN BR0/0: INCOMING CALL: VOICE ERROR: Requested circuit/channel not available(0x2C): bchan 0, call id 6

Jun 1 10:44:35.333: ISDN BR0/0: process_disconnect(): call id 0x6, call type is VOICE, b_idb 0x611BB53C, ces 1, cause Requested circuit/channel not available(0x2C)

Jun 1 10:44:35.337: ISDN: get_isdn_service_state(): idb 0x611BB53C bchan 2 is_isdn 1 Not a Pri

Jun 1 10:44:35.337: CCBRI_Go Fr Host InPkgInfo (Len=9) :

Jun 1 10:44:35.337: 7 0 1 0 6 3 18 1 89

Jun 1 10:44:35.337:

Jun 1 10:44:35.341: CCBRI_Go Fr Host InPkgInfo (Len=13) :

Jun 1 10:44:35.341: 5 0 1 0 6 3 8 1 AC 8 2 80 AC

Jun 1 10:44:35.341:

Jun 1 10:44:35.341: U99_DiscReq: CC_REL_CONF sent cid 0x6 cr 0xE1 ces 1 dsl 0

Jun 1 10:44:35.341: CCBRI_Go Fr L3 pkt (Len=4) :

Jun 1 10:44:35.341: 84 1 E1 99

Jun 1 10:44:35.341:

Jun 1 10:44:35.345: ISDN BR0/0: LIF_EVENT: ces/callid 1/0x6 HOST_DISCONNECT_ACK

Jun 1 10:44:35.345: ISDN: get_isdn_service_state(): idb 0x611BB53C bchan 2 is_isdn 1 Not a Pri

Jun 1 10:44:35.345: ISDN BR0/0: HOST_DISCONNECT_ACK: call type is VOICE

Jun 1 10:44:35.345: ISDN BR0/0: HOST_DISCONNECT_ACK: VOICE ERROR: Invalid CSM info(0xFB): bchan 0, call id 6

Jun 1 10:44:35.393: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0/0, TEI 70 changed to up

Jun 1 10:44:35.393: L3: L3_GetUser_NLCB returned NULL, message ignored cid 0x0 cr 0x0 ev 0x203 ces 1 dsl 0

Jun 1 10:44:35.669: TTY75: dropping DTR, hanging up

Jun 1 10:44:35.669: tty75: Modem: HANGUP->IDLE

Jun 1 10:44:40.685: TTY75: restoring DTR

Jun 1 10:44:41.685: TTY75: autoconfigure probe started

Jun 1 10:44:50.357: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR0/0, TEI 70 changed to down

-----------------------------------------------------

Can i do that or I must use a PRI interface? Is there any way to terminate analalog calls to BRI interface?

Thanks in advance!

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: Analog Call through BRI

Jun 1 10:44:35.333: %CSM-1-HWREV: The T1 or E1 network module is incompatible with the digital modems: MODEM_REPORT

Which module do you have ? Include "show diag".

3 REPLIES
Hall of Fame Super Gold

Re: Analog Call through BRI

Jun 1 10:44:35.333: %CSM-1-HWREV: The T1 or E1 network module is incompatible with the digital modems: MODEM_REPORT

Which module do you have ? Include "show diag".

New Member

Re: Analog Call through BRI

Hi,

Finally I found out the restrictions for the Cisco 3640 router in the following link:

http://www.cisco.com/en/US/docs/ios/12_0t/12_0t3/feature/guide/3600mbri.html

I must use different network module and not a WIC or VIC BRI interface.

Thanks

Hall of Fame Super Gold

Re: Analog Call through BRI

This is your relevant document, now 11 years old:

http://www.cisco.com/en/US/ts/fn/000/fn2128_12011998.html

291
Views
0
Helpful
3
Replies