10-03-2006 07:12 AM
Hi. Actually I've been working with a AS5300 with 120 lines. The AS reports six lines with problems. When I cheked its status, I see this messages ( With SH LINE command ):
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
* 2/36 Digital modem - DialIn - - - 0 0 0/0 -
* 2/37 Digital modem - DialIn - - - 0 0 0/0 -
* 2/38 Digital modem - DialIn - - - 0 0 0/0 -
* 2/39 Digital modem - DialIn - - - 0 0 0/0 -
* 2/40 Digital modem - DialIn - - - 0 0 0/0 -
* 2/41 Digital modem - DialIn
If you see the use's column, it is in cero. Of cuourse, those modems has problems. I wrote "clear line" command and the problem is. I shutdown the AS too, but the problem continues. Anybody knows what kind of problem is this? Anybody can help me?
Thanks a lot.
Francisco Velasco
10-04-2006 10:19 PM
Hola Franscisco,
what modems are you using ? Can you post the output of:
show modem version
show modem mapping
show version
Regards,
GNT
10-05-2006 06:34 AM
Hi Sr. First at all I appreciate a lot your help. This is the output of the "show modemcap" and "show version" commands, because our AS doesn't support your commands.
-----------------
Switch# show modemcap
default
codex_3260
usr_courier
usr_sportster
hayes_optima
global_village
viva
telebit_t3000
microcom_hdms
microcom_server
nec_v34
nec_v110
nec_piafs
cisco_v110
microcom_mimic
mica
nextport
scm
Switch# sh version
Cisco Internetwork Operating System Software
IOS (tm) 5350 Software (C5350-IS-M), Version 12.3(3g), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Fri 21-May-04 02:46 by kellythw
Image text-base: 0x6000895C, data-base: 0x61600000
ROM: System Bootstrap, Version 12.2(1r)1, RELEASE SOFTWARE (fc1)
BOOTLDR: 5350 Software (C5350-BOOT-M), Version 12.2(2)XB2, EARLY DEPLOYMENT RELE
ASE SOFTWARE (fc1)
accserver5 uptime is 1 week, 1 hour, 14 minutes
System returned to ROM by power-on
System image file is "flash:c5350-is-mz.123-3g.bin"
cisco AS5350 (R7K) processor (revision T) with 262144K/131072K bytes of memory.
Processor board ID JAE0822JW8B
R7000 CPU at 250Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3 Cache
Last reset from power-on
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
Primary Rate ISDN software, Version 1.1.
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x32,
Board Hardware Version 3.34, Item Number 800-5171-02,
Board Revision C0, Serial Number JAE0822JW8B,
PLD/ISP Version 2.2, Manufacture Date 26-May-2004.
Processor 0x14, MAC Address 0x0FF7D047B2
Backplane HW Revision 1.0, Flash Type 5V
2 FastEthernet/IEEE 802.3 interface(s)
130 Serial network interface(s)
120 terminal line(s)
4 Channelized E1/PRI port(s)
512K bytes of non-volatile configuration memory.
65536K bytes of processor board System flash (Read/Write)
16384K bytes of processor board Boot flash (Read/Write)
Configuration register is 0x2102
--------
Thanks again and I'll waut your answer.
Reggards,
Francisco Velasco
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: