Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cisco 2611xm and NM-32a module - HELP

I have a question I'm not sure if it difficult or not. I have a NM-32a in

my 2611xm using IOS version: 2600-jk9s-mz.123-24.b. The problem is that I cannot setup the 2611xm to connect to my other cisco devices. I have read Cisco's Configuring a Terminal / Comm server (Doc ID:5466) and it has not helped me I still can't connect any of the devices. Any idea?

Access-Server(config)#do sh run

version 12.3

!

hostname Access-Server

!

boot-start-marker

boot-end-marker

!

enable secret xxx

!

memory-size iomem 10

no network-clock-participate slot 1

no network-clock-participate wic 0

no aaa new-model

ip subnet-zero

!

!

ip host Router1 2033 172.21.1.1

ip host Router2 2034 172.21.1.1

ip host Router3 2035 172.21.1.1

ip host Router4 2035 172.21.1.1

ip host Router5 2036 172.21.1.1

!

username cisco password 0 cisco

!

!

interface Loopback1

ip address 172.21.1.1 255.255.255.0

!

interface FastEthernet0/0

ip address 139.x.x.50 255.255.255.0

duplex auto

speed auto

!

line con 0

line 33 64

transport input telnet

flowcontrol hardware

line aux 0

line vty 0 4

password cisco

login

Access-Server#sh line

Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int

* 0 CTY - - - - - 2 0 0/0 -

* 33 TTY 9600/9600 - - - - - 0 48 52/158 -

* 34 TTY 9600/9600 - - - - - 1 25 53/164 -

* 35 TTY 9600/9600 - - - - - 0 88 8/26 -

* 36 TTY 9600/9600 - - - - - 0 13 17/54 -

* 37 TTY 9600/9600 - - - - - 1 0 0/0 -

38 TTY 9600/9600 - - - - - 2 0 0/0 -

39 TTY 9600/9600 - - - - - 0 11 12/37 -

40 TTY 9600/9600 - - - - - 0 11 19/59 -

41 TTY 9600/9600 - - - - - 0 17 27/82 -

42 TTY 9600/9600 - - - - - 0 37 36/110 -

43 TTY 9600/9600 - - - - - 0 0 0/0 -

44 TTY 9600/9600 - - - - - 0 23 0/0 -

45 TTY 9600/9600 - - - - - 0 0 0/0 -

46 TTY 9600/9600 - - - - - 0 0 0/0 -

47 TTY 9600/9600 - - - - - 0 27 0/0 -

48 TTY 9600/9600 - - - - - 0 0 0/0 -

49 TTY 9600/9600 - - - - - 0 11 0/0 -

50 TTY 9600/9600 - - - - - 0 1 0/3 -

51 TTY 9600/9600 - - - - - 0 0 0/0 -

52 TTY 9600/9600 - - - - - 0 0 0/0 -

53 TTY 9600/9600 - - - - - 0 0 0/0 -

54 TTY 9600/9600 - - - - - 0 0 0/0 -

3 REPLIES

Re: Cisco 2611xm and NM-32a module - HELP

Still you seem to have missed a few settings. the following must be in the config:

line 33 64

transport preferred telnet

transport input all

Please post a "sh line" for one of the lines on the NM32A.

regards,

Leo

New Member

Re: Cisco 2611xm and NM-32a module - HELP

thanks lgijssel,

it works.

However, I cant ssh to the router remotely. Please advise

Re: Cisco 2611xm and NM-32a module - HELP

697
Views
10
Helpful
3
Replies