Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cisco 2811 Dial up Internet Configuration Problem

I have the following dial up problem please help me overcome this problem

i have configured Cisco 2811 to be used as a dial up router with one E1, so that subscriber can dial in and use the internet.

the problem is that when adding "interface Group-Async1" the command (group-range 1 30) when i excute this command it indicates accepting the command but when i show config, i am still getting (group-range 1 1.

below is the show ver result.

STEL#sh ver

Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(21a), RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2008 by Cisco Systems, Inc.

Compiled Mon 29-Sep-08 16:02 by prod_rel_team

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

STEL.Hargeisa uptime is 3 minutes

System returned to ROM by power-on

System image file is "flash:c2800nm-advipservicesk9-mz.124-21a.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco 2811 (revision 53.50) with 247808K/14336K bytes of memory.

Processor board ID FHK1204F3UT

2 FastEthernet interfaces

31 Serial interfaces

1 Channelized E1/PRI port

1 Virtual Private Network (VPN) Module

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

63808K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

Hassan R.

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: Cisco 2811 Dial up Internet Configuration Problem

Both of them.

Please remember to rate useful posts with the scrollbox below.

5 REPLIES
Hall of Fame Super Gold

Re: Cisco 2811 Dial up Internet Configuration Problem

You cannot use this 2811 for dial-up because it doesn't have any modem. You need an PVDM2-36DM and HWIC-1CE1T1-PRI. See:

http://www.cisco.com/en/US/docs/ios/12_4t/12_4t11/htpvdm2.html

New Member

Re: Cisco 2811 Dial up Internet Configuration Problem

Thanks for your help

Hall of Fame Super Gold

Re: Cisco 2811 Dial up Internet Configuration Problem

You're welcome, please remember to rate useful posts with the scrollbox below.

New Member

Re: Cisco 2811 Dial up Internet Configuration Problem

Do I need both cards or one of them:

PVDM2-36DM and HWIC-1CE1T1-PR

Hall of Fame Super Gold

Re: Cisco 2811 Dial up Internet Configuration Problem

Both of them.

Please remember to rate useful posts with the scrollbox below.

412
Views
0
Helpful
5
Replies