Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cisco 871 & IRZ MC55IT

Hello

Please, help me with my problem

Can't connect and get IP address via GPRS

I read many articles about this problem but can't solve it.

                                          Config

!

chat-script gsm "" AT OK AT&F OK "AT\\Q3" OK "AT+CGDCONT=1,IP,www.umc.ua" OK "ATD*99***1#" TIMEOUT 30 CONNECT

chat-script reset "" \d\d\d+++\d\d\d

!

interface Async1

description gsm

ip address negotiated

encapsulation ppp

load-interval 30

dialer in-band

dialer string "*99***1#" modem-script gsm

dialer-group 1

async mode dedicated

ppp authentication pap chap callin

ppp chap password 0 igprs

ppp pap sent-username igprs password 0 igprs

!

dialer-list 1 protocol ip permit

!

line aux 0

script dialer gsm

script reset reset

modem InOut

exec-character-bits 8

special-character-bits 8

no exec

transport input all

escape-character BREAK

stopbits 1

speed 115200

flowcontrol hardware

!

                                            Log

*08:59:33.523: CHAT1: Chat script reset finished, status = Success

*08:59:33.523: TTY1: Modem: HANGUP->HANGUP

*08:59:33.523: TTY1: no timer type 0 to destroy

*08:59:33.523: TTY1: no timer type 1 to destroy

*08:59:33.523: TTY1: no timer type 3 to destroy

*08:59:33.523: TTY1: no timer type 4 to destroy

*08:59:33.523: TTY1: no timer type 10 to destroy

*08:59:33.523: TTY1: no timer type 2 to destroy

*08:59:33.823: TTY1: dropping DTR, hanging up

*08:59:33.823: TTY1: Set DTR to 0

*08:59:33.823: tty1: Modem: HANGUP->IDLE

*08:59:38.827: TTY1: restoring DTR

*08:59:38.827: TTY1: Set DTR to 1

*08:59:39.827: TTY1: DSR came up

*08:59:39.827: TTY1: no timer type 1 to destroy

*08:59:39.827: TTY1: no timer type 0 to destroy

*08:59:39.827: TTY1: no timer type 2 to destroy

*08:59:39.827: tty1: Modem: IDLE->(unknown)

*08:59:41.827: %LINK-3-UPDOWN: Interface Async1, changed state to up

*08:59:41.827: As1 DDR: Dialer statechange to up

*08:59:41.827: As1 DDR: Dialer received incoming call from *99***1#

*08:59:41.827: As1 PPP: Using dialer call direction

*08:59:41.827: As1 PPP: Treating connection as a callin

*08:59:41.827: As1 PPP: Session handle[FF00000B] Session id[6]

*08:59:41.827: As1 PPP: Phase is ESTABLISHING, Passive Open

*08:59:41.827: As1 LCP: State is Listen

*08:59:43.811: As1 LCP: TIMEout: State Listen

*08:59:43.811: As1 PPP: Authorization required

*08:59:43.811: As1 LCP: O CONFREQ [Listen] id 51 len 24

*08:59:43.811: As1 LCP:   ACCM 0x000A0000 (0x0206000A0000)

*08:59:43.811: As1 LCP:   AuthProto PAP (0x0304C023)

*08:59:43.811: As1 LCP:   MagicNumber 0x239BF33D (0x0506239BF33D)

*08:59:43.811: As1 LCP:   PFC (0x0702)

*08:59:43.811: As1 LCP:   ACFC (0x0802)

*08:59:45.827: As1 LCP: TIMEout: State REQsent

*08:59:45.827: As1 LCP: O CONFREQ [REQsent] id 52 len 24

*08:59:45.827: As1 LCP:   ACCM 0x000A0000 (0x0206000A0000)

*08:59:45.827: As1 LCP:   AuthProto PAP (0x0304C023)

*08:59:45.827: As1 LCP:   MagicNumber 0x239BF33D (0x0506239BF33D)

*08:59:45.827: As1 LCP:   PFC (0x0702)

*08:59:45.827: As1 LCP:   ACFC (0x0802)

*08:59:47.843: As1 LCP: TIMEout: State REQsent

*08:59:47.843: As1 LCP: O CONFREQ [REQsent] id 53 len 24

*08:59:47.843: As1 LCP:   ACCM 0x000A0000 (0x0206000A0000)

*08:59:47.843: As1 LCP:   AuthProto PAP (0x0304C023)

*08:59:47.843: As1 LCP:   MagicNumber 0x239BF33D (0x0506239BF33D)

*08:59:47.843: As1 LCP:   PFC (0x0702)

*08:59:47.843: As1 LCP:   ACFC (0x0802)

*08:59:48.827: TTY3: timer type 1 expired

*08:59:48.827: TTY3: Exec timer (continued)

*08:59:49.859: As1 LCP: TIMEout: State REQsent

*08:59:49.859: As1 LCP: O CONFREQ [REQsent] id 54 len 24

*08:59:49.859: As1 LCP:   ACCM 0x000A0000 (0x0206000A0000)

*08:59:49.859: As1 LCP:   AuthProto PAP (0x0304C023)

*08:59:49.859: As1 LCP:   MagicNumber 0x239BF33D (0x0506239BF33D)

*08:59:49.859: As1 LCP:   PFC (0x0702)

*08:59:49.859: As1 LCP:   ACFC (0x0802)

*08:59:51.875: As1 LCP: TIMEout: State REQsent

*08:59:51.875: As1 LCP: O CONFREQ [REQsent] id 55 len 24

*08:59:51.875: As1 LCP:   ACCM 0x000A0000 (0x0206000A0000)

*08:59:51.875: As1 LCP:   AuthProto PAP (0x0304C023)

*08:59:51.875: As1 LCP:   MagicNumber 0x239BF33D (0x0506239BF33D)

*08:59:51.875: As1 LCP:   PFC (0x0702)

*08:59:51.875: As1 LCP:   ACFC (0x0802)

*08:59:53.891: As1 LCP: TIMEout: State REQsent

*08:59:53.891: As1 LCP: O CONFREQ [REQsent] id 56 len 24

*08:59:53.891: As1 LCP:   ACCM 0x000A0000 (0x0206000A0000)

*08:59:53.891: As1 LCP:   AuthProto PAP (0x0304C023)

*08:59:53.891: As1 LCP:   MagicNumber 0x239BF33D (0x0506239BF33D)

*08:59:53.891: As1 LCP:   PFC (0x0702)

*08:59:53.891: As1 LCP:   ACFC (0x0802)

*08:59:55.907: As1 LCP: TIMEout: State REQsent

*08:59:55.907: As1 LCP: O CONFREQ [REQsent] id 57 len 24

*08:59:55.907: As1 LCP:   ACCM 0x000A0000 (0x0206000A0000)

*08:59:55.907: As1 LCP:   AuthProto PAP (0x0304C023)

*08:59:55.907: As1 LCP:   MagicNumber 0x239BF33D (0x0506239BF33D)

*08:59:55.907: As1 LCP:   PFC (0x0702)

*08:59:55.907: As1 LCP:   ACFC (0x0802)

*08:59:57.923: As1 LCP: TIMEout: State REQsent

*08:59:57.923: As1 LCP: O CONFREQ [REQsent] id 58 len 24

*08:59:57.923: As1 LCP:   ACCM 0x000A0000 (0x0206000A0000)

*08:59:57.923: As1 LCP:   AuthProto PAP (0x0304C023)

*08:59:57.923: As1 LCP:   MagicNumber 0x239BF33D (0x0506239BF33D)

*08:59:57.923: As1 LCP:   PFC (0x0702)

*08:59:57.923: As1 LCP:   ACFC (0x0802)

*08:59:59.939: As1 LCP: TIMEout: State REQsent

*08:59:59.939: As1 LCP: O CONFREQ [REQsent] id 59 len 24

*08:59:59.939: As1 LCP:   ACCM 0x000A0000 (0x0206000A0000)

*08:59:59.939: As1 LCP:   AuthProto PAP (0x0304C023)

*08:59:59.939: As1 LCP:   MagicNumber 0x239BF33D (0x0506239BF33D)

*08:59:59.939: As1 LCP:   PFC (0x0702)

*08:59:59.939: As1 LCP:   ACFC (0x0802)

*09:00:01.955: As1 LCP: TIMEout: State REQsent

*09:00:01.955: As1 LCP: O CONFREQ [REQsent] id 60 len 24

*09:00:01.955: As1 LCP:   ACCM 0x000A0000 (0x0206000A0000)

*09:00:01.955: As1 LCP:   AuthProto PAP (0x0304C023)

*09:00:01.955: As1 LCP:   MagicNumber 0x239BF33D (0x0506239BF33D)

*09:00:01.955: As1 LCP:   PFC (0x0702)

*09:00:01.955: As1 LCP:   ACFC (0x0802)

*09:00:03.971: As1 LCP: TIMEout: State REQsent

*09:00:03.971: TTY1: Async Int reset: Dropping DTR

*09:00:03.971: TTY1: Set DTR to 0

*09:00:03.971: As1 LCP: State is Listen

*09:00:05.971: %LINK-5-CHANGED: Interface Async1, changed state to reset

*09:00:05.971: As1 PPP: Sending Acct Event[Down] id[14]

*09:00:05.971: As1 LCP: State is Closed

*09:00:05.971: As1 PPP: Phase is DOWN

*09:00:08.971: TTY1: no timer type 0 to destroy

*09:00:08.971: TTY1: no timer type 1 to destroy

*09:00:08.971: TTY1: no timer type 3 to destroy

*09:00:08.971: TTY1: no timer type 4 to destroy

*09:00:08.971: TTY1: no timer type 10 to destroy

*09:00:08.971: TTY1: no timer type 2 to destroy

*09:00:08.971: Async1: asking modem_process to hangup TTY1

*09:00:08.971: CHAT1: Attempting line reset script

*09:00:08.971: CHAT1: Matched chat script reset to string reset

*09:00:08.971: CHAT1: Asserting DTR

*09:00:08.971: TTY1: Set DTR to 1

*09:00:08.971: CHAT1: Chat script reset started

*09:00:08.971: CHAT1: Sending string: \d\d\d+++\d\d\d

*09:00:10.971: %LINK-3-UPDOWN: Interface Async1, changed state to down

It seems that only incoming trafic are allowed.

Why don't modem call number?

Thanks

3 REPLIES

Re: Cisco 871 & IRZ MC55IT

Hi! Did you defined your APN? I've posted blogpost here about grps connection on 880 router, maybe you will find it helpful http://betep.wpl.ru

Sent from Cisco Technical Support iPhone App

New Member

Cisco 871 & IRZ MC55IT

Hi!

Thanks for your attention

I define APN in chat-script gsm but cisco don't use it as you see in log.

If I start chat-script gsm manually it performed well but situation is still the same, I can't get IP address.

Re: Cisco 871 & IRZ MC55IT

Did you try this one:

cellular 0 gsm profile create 1 www.umc.ua pap ipv4

Are you shure about dialed digits?

I can't see where you specified your login and password.

515
Views
0
Helpful
3
Replies
CreatePlease login to create content