11-24-2012 04:53 AM
Hi Guys, Please help me on this.. I am trying to setup a lab with the basic one... whenever I tried to telnet to my TERMSERVER 192.168.1.7 frm my PC, its always resetting after few mins.. it wont stay open anymore.. means I have to retelnet to 192.168.1.7 and enter the login/password/.... My Router is 2610 with NM-16AS
My setup goes as below;
MYPC -------->>> Netgear switch-------------->>>> cisco 2610 Terminal server
192.168.1.1/24 192.168.1.7/24
My configs are below which is pretty basic..
Term2600#sh run
Building configuration...
Current configuration : 1470 bytes
!
! Last configuration change at 12:20:52 UTC Sat Nov 24 2012
! NVRAM config last updated at 12:20:56 UTC Sat Nov 24 2012
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Term2600
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
ip subnet-zero
!
!
no ip domain lookup
!
ip host MR7-O2 2042 1.1.1.1
ip host MR5-N3 2035 1.1.1.1
ip host MR4-N6 2038 1.1.1.1
ip host MR6-O3 2043 1.1.1.1
ip host MR8-O1 2041 1.1.1.1
ip host MR2-N8 2040 1.1.1.1
ip host MR3-N7 2039 1.1.1.1
ip host FR 2048 1.1.1.1
ip host R5 2037 1.1.1.1
ip host R2 2034 1.1.1.1
ip host R1 2033 1.1.1.1
ip host SW3 2046 1.1.1.1
ip host SW4 2047 1.1.1.1
!
ip cef
!
!
interface Loopback100
ip address 1.1.1.1 255.255.255.255
!
interface Ethernet0/0
ip address 192.168.1.7 255.255.255.0
half-duplex
no cdp enable
!
interface BRI0/0
no ip address
encapsulation hdlc
shutdown
!
no ip http server
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.1.254
!
!
line con 0
password cisco
login
line 33 48
exec-timeout 35791 23
transport input all
line aux 0
line vty 0 4
password cisco
login
transport input telnet
line vty 5 25
password cisco
login
transport input telnet
line vty 26 65
login
transport input all
line vty 66 91
password cisco
logging synchronous
login
transport input all
!
!
end
Term2600#sh ver | i ima
System image file is "flash:c2600-j1s3-mz.123-26.bin"
Term2600#
Term2600#
Term2600#sh diag
Slot 0:
C2610 1E Mainboard Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 2.3
PCB Serial Number : JAD044506N0 (239165711)
Part Number : 73-2839-13
RMA History : 00
RMA Number : 0-0-0-0
Board Revision : C0
Deviation Number : 0-0
Product (FRU) Number : C2610 - 1E
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 91 41 02 03 C1 17 4A 41 44 30 34 34
0x10: 35 30 36 4E 30 20 28 32 33 39 31 36 35 37 31 31
0x20: 29 82 49 0B 17 0D 04 00 81 00 00 00 00 42 43 30
0x30: 80 00 00 00 00 FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 1:
BRI S/T - 2186 WAN daughter card
Hardware revision 1.3 Board revision A0
Serial number 26988006 Part number 800-01833-03
FRU Part Number WIC-1B-S/T=
Test history 0x0 RMA number 00-00-00
Connector type Wan Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 07 01 03 01 9B CD E6 50 07 29 03 00 00 00 00
0x30: 50 00 00 00 01 11 08 01 FF FF FF FF FF FF FF FF
Slot 1:
Async Port adapter, 16 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 0.1 Board revision H0
Serial number 28934401 Part number 800-02244-05
FRU Part Number: NM-16A=
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x00: 01 62 00 01 01 B9 81 01 50 08 C4 05 00 00 00 00
0x10: 88 00 00 00 02 08 28 00 FF FF FF FF FF FF FF FF
Term2600#
Thanks..
12-06-2012 03:34 AM
try and configure the below
line 33 48
exec-timeout 0 0
line vty 0 91
exec-timeout 0 0
HTH>
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: